It's all about the Software

Hi!
The firmware loads, the device is identified as Model: RX999, Firmware: v2.2, but there is no RX999 in Definitions, and searching for RX-888 does not find the device

18:30:29.354: Select Radio> -
18:30:29.354: Select Radio> Selecting Radio...

Good afternoon all.

Of late I have noticed that my bandplan disappears. It never used to, and may well have started when I updated to 3.4 b4138.

There appears to be no rhyme nor reason, one minute it's there, the next not. I have no reliable way...

I have SDR Console's satellite interface set to show the Tracker and Automatic Schedule windows undocked. Whenever I start SDR console, the satellite interface automatically loads and the Show toolbar has the two window buttons in the depressed...

Done, thanks.

Update Default cluster

spider.sdr-radio.com:8000
The DX Cluster node at spider.sdr-radio.com will close on April 1st,
2026. Please select another node.

Replace Default Satellite TLE links - None of them work anymore

I suggest:

I'm running an automated process which grabs screen shots of the satellite window during a satellite pass. There is nothing in the window title which allows me to reliably get its handle using ::FindWindow.

The best workaround I currently have is...

SDR Console currently only supports control of external radio using Omni-Rig. While Omni-Rig is a great package it has some serious downsides.

The root problem is that it is very difficult to make Omni-Rig co-exist with other radio control...

With Auto Mute disabled, Tracking enabled, when I key the Xiegu external mic PTT and transmit, several seconds or more into the transmission, the SDRC stops the audio, then the Waterfall goes dark and the spectrum drops in magnitude. Just like the...

Hi, with elad fdm duo if I play an audio track and then send it to transmission to be listened to the audio track is heard low and with noises as if I had some high gain level.....

If I listen to the file with Windows the track sounds great but...

Good morning, I'm explaining my little problem again, Brick-2 configured as ANAN-10-Hermes everything works except that if I go into transmission the power goes out I can make QSO but I DON'T see the filter in TX on the Panadapter, the span goes...

Hi, I’m new here on the forum.

Hello folks,
I am using SDRC V3.2 as a remote panadaptor.
In the remote shack, I connect RSP-1A to IF output of FTDX5000 and run the SDRC server on a server PC.
On the client side, I can use SDRC as Panadaptor syncronizing VFO-A of FTDX5000 via...

Hello Simon, et. al.,

I'd like to offer my encouragement and perhaps other to further the development of a G2 Radio Definition for SDR Console. It seems more development is coming from Apache Labs along similar lines...G1 and the ANAN-G2-1K 1000W....

I am pretty sure all settings are correct. Frequency is set, satellite in list of automatic scheduler, I/Q recording is checked, normal scheduler is off, the map shows AOS and auto scheduling on.
A few passes were randomly recorded, but most of them...

Hello.

When usinf Analyzer crop selection, BW is not correct so you get an error. If selected by hand, no problem.

SDRConsole_bug.jpg

Best regards.
ANgazu.

Installed a much longer antenna after replacing it back in May due to winds. I also discovered long runs of galvanized fence wire laying on the ground in storage , so I connected one of them to the ground lug of the 9:1 unun. The unun was already...

This is attempt #2

For my ic756pro I can click the waterfall or rf spectrum to tune, but it is not reliable, it will miss, and the logs say this when it happens:
SDR>Ext IC-756 Pro> Frequency 7.179.400, BLOCKED

I have confirmed this is the only omnirig piece of...

I would like to request that the ability to switch from internal clock to external clock ( ck1 ) be added. Probably under the radio options tab. As an EME operator, I need an exact frequency reference. It seems that the feature is available in the...

Hello.
Many modern communication systems use unique ACF (autocorrelation) values, so this algorithm would be very useful for rapid system identification. It is also very useful for viewing the PRF of OTHRs.

If this request is accepted and included...

Hi all.

The CROP tool in the Data file analyzer shows the parameters of the selected area.
Perhaps you can ad a control to export those data to the Data File Editor and open it for fine tuning and processing the selected area.

data-export.jpg...

Using Limesdr RX and TX on AO100 in 3.4 console I often have to retry pressing the TX button before the Lime actually transmits. The button changes color every try but the lime only reacts like 50% of the time.

I run 3.4 on both W7 and W11 machines, same driver.

Limesdr is found correctly in device manager.

SDR console cannot find limesdr on the W11 machine.

The SDR console recognizes different USB cards, but controls them individually.
It's not possible to have a single PTT command on multiple radios connected to the software.
In my case I have 4 radios and amplifiers in separate boxes, and I can't...