It's all about the Software

This is the scenario: I'm using an IC705 for transmit/receive on Es'Hail-2. I have a Lime SDR attached as an external radio to enable me to monitor my transmit signal via the satellite as required. The Lime tracks the Icom OK.

However, my transmit...

Helllo, recently tried out the MIDI functionality which is really nice. Thanks for that. I have found that if I make a slider for volume control that has a range of 0 to 127, the software detects it properly and sets the values in the midi config...

Hello, struggling on connecting Prosistel D controller to show antenna azimuth on Simons map. The controller is connected to PC via USB and creates port. The rest is unclear how to connect to the map. Have been using Yaesu rotator successfully...

Had a bad case of Sciurus carolinensis or Tamiasciurus hudsonicus!
Grey squirrel or Red squirrel decided to chew on the insulation, and wires of the antenna about 4' from the 9:1 unun. Both ends were stripped about 2 so I wrapped the two back...

Hi,

On SDR-Console V 3.3 when I try to select Hermes Lite 2 in the Search option, I am given the below option

-> Default
-> Extended
-> Fixed Address

But when I select the option of PlutoSDR in the search option,I do not find any of the options...

Hi,

SDR Console 3.3 / Pluto Plus / CN-0417 Preamp / DX Patrol 12w Amp.

When I first power up the Pluto+ and run SDR Console I can’t get any TX power out on voice or tone. The TX button in SDRC changes colour and I am showing a modulated signal or...

Hello,

Many times, I'm just listening to some radio while the satellite AOS starts without paying attention. It is switching at LOS, but if changed, it won't come back automatically when the recording starts. I have to do that manually.

Hi all,

This must be something I am doing wrong, as I have searched the forum and find no mention of this issue.

SDR Console 3.3 / Pluto Plus / CN-0417 Preamp / DX Patrol 12w Amp.

When I first power up the Pluto+ and run SDR Console I can’t get...

Hello,

It would be nice to add the ability to record Audio with the scheduler. Currently, only Data recording is allowed.

Hello,

It would be nice to turn the radio on (and record) automatically when the scheduler enters AOS and turn it off after LOS. This will allow keeping the system off while idle, and only turn on radio when required.

In the old days of analogue broadcast satellites it was quite easy to align the dish using a sat finder with an audio output where the tone frequency corresponded to signal strength.
The higher the tone the stronger the signal.
If it already exists,...

Hello all!

It looks like that the (latest 3.3 LTS) SDR-Radio.com (V3) installer does not report the application installed version to the system:

screenshot.png

Is there any way to find SDR-Radio.com version (without opening the application)...

Hello, I'm using SDR console and I'm controlling it via CAT. My receiver is an airspy hf+, connected via spy server.
When I set a new frequency via CAT, outside the currently visualised spectrum, sometimes the receiver becomes mute. As soon as I...

HI,

I'm using Version 3.3, Build 3195 on Windows 11 and noticed the following reproducible two bugs:
After pressing the E2 button (Filter Low) on the ELAD TM-2 controller, the programm crashes (a message pop's up: please wait - but nothing happens)...

Hello,
Here is the context: I am using a FT-991A on QO-100 with DX Patrol converters (144.500 MHz IF). Most of the time, I do SSB or FT8 modes.
A Panadapter from SDR Kits is installed ( which outputs a 70ish MHz IF to an Airspy HF+ Discovery.

The...

One enduring memory from childhood was my father suborning BBC Research Department colleagues at Kingswood to help align our very first simple Band II dipole.

They came equipped with an impressive test set which was described in Wireless World ,...

I have tried to capture diagnostics so apologies for long post

Having problem with ELAD FMduo and SDR server.
It was working up til 2 weeks ago.

My setup have a win 11 laptop running v3117 (sdrserver) with an airspy hf+ discovery and elad fm-duo...

Hi!

the frequency range on the RX888 is tricky. SDRconsole swithced too early from the HF port to the VHF port. When the center marker of the band width selector hits 16Mhz the VHF is choosen.
As the RX888 can run the HF until 30 Mhz, this is far...

The Fusion 13 option doesn't work so well and this is on a 2021 Mac so it's fairly fast. Lots of pops etc and slow. Never did get the receiver panel to show SSB. Audio very poor on FM. The box to set configuration wasn't consistent. Maybe Parallels...

Firstly thank you Simon - I love SDRConsole...

One feature is if the frequency database could have a filter by time button, so when I click on a frequency, it would only show stations scheduled to be on air now, with option to see all .

I enjoy using Console as the only SDR software in my shack. It is fantastic! I only wish that my Flex 1500 could use it.
Is it possible?
I'm afraid I know the answer. I just had to ask so I can quit dreaming...

Thank you,
John

Hi all and thanks for the add. I have a quick query.

I've recently come to the software and am trying it out with my RSPDX and so far so good. So my query is is there an easy way of importing the Mem Panels from SDR Uno to Console's memories or do...

Version 3.3 Build 3048 , i just updated to the latest version August 1st 2023 and very nice .
I really like the auto upgrade feature (one just runs the downloaded exe) and so far it does not mess anything else up like the saved memory's and Markers...

Simon,

At some time in the future, would it be possible to optionally move the Band Plan from the bottom of the pane to the top? It's just a bit less busy in that location.

Thanks!

After running perfectly for several weeks with Phil's KA9Q-radio SW, last Saturday my RX888 suddenly failed.

The failure mode suggests that one or more of the BGA pins of the the FX3 have desoldered, and a FLIR scan of a FX3 showed it running at...