It's all about the Software

Hi Im not sure what happened.
Earlier I installed SDR Console v3.4 (SDR-Radio V3.4, 64-bit, 2026-02-11_1214.exe) and Cypress FX3 Win10 in combination with my RX888 MKII on a NuBox M6 24GB RAM Win11Pro 64bit, which used to work very well. I didn't do...

Hi everyone, I'm having a strange situation with SDR Console. If I set the direct sampling rate to 192 kHz, when I open the SDR Console software, the sound card switches to 48 kHz and the microphone crackles, making it difficult to hear. The sound...

I am running v3.4 with a sdrplay rspdx.l noticed that my 40 meter band does not end at 7.300. Is there a way to set my location like my grid square, iTunes to maje my bands use the correct band plan.i have it hook up to my ft-891 with omnirig.
Hope...

Hi everyone,

I'm experiencing a display issue in SDR-Console v3.4 while using an ANAN Hermes (OpenHPSDR) radio.

The Problem:
Whenever I go into transmission (either by clicking the TUNE button or via PTT), the main spectrum/waterfall display drops...

I am using W7 for ages to run my Lime SDR QO100 station. Never issues...

Today it came with a dialog box when trying to start:

SDR Console.exe - Entry point not found

The procedue entry point GetSystemTimePreciseAsFileTime could not be located...

Hi guys, I'm having a major problem with the TX audio and with HERMES LITE. My voice cuts out in spots, and the watts are delayed! There's a lot of latency. I tried lowering the buffer, setting the TX and RX sampling rate on my sound card to 48 kHz,...

Greetings Chaps,
I have been using the Signal History feature in SDR Console V3.4 and find it very easy to use. There appears to be a problem with the exported csv files. For example here are a few lines from an exported file:...

My horizonal Receiver Pane shows (a) a dBm meter, and (b) a green overlay (not sure what it is called) which appears to select the audio bandwidth with the number in the middle.

1. Sometimes I lose both the dBm meter and green overlay. How do I...

In the horizontal Receiver pane, I want to label a frequency with the name of a radio station; Google Gemini tells me to use the Frequency Database, but I can't see the Add button it refers to.
What am I missing?
sdr frequency database...

Absolute newbie, I have just installed SDR Console and I think I have successfully selected my RTL-SDR USB dongle radio, this one:

I am following a Youtube quickstart guide, which shows a Radio control section in the RX panel after Filter , eg....

When I tune, they receiver window waterfall goes blank, and starts again.

While I'm not 100% sure, I don't think this used to happen as my workflow is to use the small receive window to tune to a signal with greater precision whilst leaving my...

Ciao,

I have a problem with USB relay list recognition with SDR Consol, and The refresh list command has no effect.

It's not due to the relays, which are identical.
If I swap the USB connections, the problem persists.
It's not a USB cable issue....

Hello,

I would like to use an SDR at a remote location while transmitting using my shack HF radio. I have figured out most things but the one difficulty I have is how to mute the RX noise in the shack when I TX.

The SDR will be miles away from my...

I have a range of favourites setup for different frequency ranges, allowing me to easily flick back and forth as needed. The issue however is that I need different levels of RF and Visual gain for frequencies above about 30 MHz.

Is there any way...

Hi Guys

i'm using sdr Lime Mini USB as IF RTX at 72 MHz, with up conversions home made HF Transceiver

To have correct USB/LSB monitor vision on RX , i must use the function Inverted Spectrum starting SDR console.

But on TX, I haven't found how to...

Hello everyone, I really don't know what I'm doing wrong, after half a Sunday searching, reading, filling up ChatGTP with my problem, so I have a help question. I want to see the downlink frequency of a QO-100 beacon in SDR Console v3.3 or 3.4....

Can SDR Console decode P25 Phase 2? If so can someone explain how to set it up?

Scott

Hi All,

I've realised after having my SDRplay in Console that the noise blanket does not work.

I switched to RX and TX on the radio and the NB was very good at removing the electric fence noisy on the common grazing area near my station....

Hi all ..

First of all ...I love this software...
However i do have a problem in conjunction with my USB Audio card and ...my SDRPlay RSPDx R2 ...

It seems as if the audio buffer sizes vary ...so I mute the audio on TX and reduce the IQ by the...

Hello,

Blame this question, and the others I will undoubtedly have
on old-age . A really great excuse for most anything.

Back to using, and learning again, the program after a long time away from
due to medical issues.

Incredible program.

Am I...

I tried opening additional receiver windows to run different SDRs, but instead of additional windows opening, additional columns with different colors appeared on the same screen. Now, I can't seem to figure out how to close any of them or open...

Hi all
I need to re-install SDR Console on a new computer.
Is there a config file that I can transfer from one computer to the other so I do not have to spend hours reconfiguring ? If so, how is it named, and where is it located ?

TU + 73
Paul F6EXV

Hello,

Will blame the following most basic question
on old age now. Great excuse for most anything.

Could someone please give me the link to the latest
version I should download ? (any reason for a very basic contemplated user to download a Beta...

Dear G4ELI,

I made a silly post a while back, and then I bought an SDRplay and SDRSwitch.

V3.4 saw the SDR and ...setup Omnirig....and my mind was blown about twenty minutes later as I pulled in tiny signals and ramped up DSP ...

This is the...

Hello:

First let me say this is an AWESOME piece of software. I have a question: is there a place where I can set the received CW to exactly match my Kenwood TS590SG? I see I can change the filtering of course. But can't see where I can change the...