It's all about the Software

I'm observing SDRC crashing when using 8 MHz bandwidth. This has been a long running problem I've never reported because I seldom use more than 2 MHz of bandwidth and the crashing at 8 MHz of bandwidth is at random times.

Though there may be a...

Just noticed this error(?). When selecting Pre-Amp on/off a window pops up saying the AGC must be off? Pre-amp works just fine on or off with AGC on.
Just uploaded the latest, V3.3 build 3236 on a W10 laptop
See screenshot

73 Kriss KA1GJU

Hello,

I'm having an External Radio Error During program Launch with the current and last few Beta versions. I'm using a TS-590SG with SDRPlay's RSP1a SDR and OmniRig. During SDR Console program startup there is a really long delay before the the...

Hi,

SDR Console 3.3 / Pluto Plus / CN-0417 Preamp / DX Patrol 12w Amp.

When I first power up the Pluto+ and run SDR Console I can’t get any TX power out on voice or tone. The TX button in SDRC changes colour and I am showing a modulated signal or...

For me and another radio amateur friend, the sensitivity in the display dropped drastically after installing 3.3. Where previously S9+5 were at the top of the upper QO-100 beacon, I only saw S3.
We had installed the new version over the old one 3.2,...

Hi
Just got my SDR Blog V4 in the mail. Installed it and it works nicely with SDR console locally along with SDR Blog V3 (working nicely in locally and server mode). I have set up the SDR Console Server the SDR Blog V4 seems not to work correctly....

Hello all!

It looks like that the (latest 3.3 LTS) SDR-Radio.com (V3) installer does not report the application installed version to the system:

screenshot.png

Is there any way to find SDR-Radio.com version (without opening the application)...

Hi Simon,

I'm using now since a few months SDR-Console and I'm very happy with the program, I'm using the latest version 3.3 with the latest build from December last year.

I have 2 issues, one related to the hanging of the program, but I think I...

Good morning everyone!..I'm trying to use 2 instances of SDR Console connected to 2 RSP1As (and obviously to 2 different antennas) with Log4OM2 via Omnirig and related serial ports emulated via com0com

At that time....

launching the first instance...

Hello, I'm using SDR console and I'm controlling it via CAT. My receiver is an airspy hf+, connected via spy server.
When I set a new frequency via CAT, outside the currently visualised spectrum, sometimes the receiver becomes mute. As soon as I...

Nice to meet you everyone.

I was listening to FM stereo broadcast on SDR-Console v3.1 with headphones and noticed that the left and right sounds were reversed. Sounds normal on SDR# and SDR++. I thought I might have made a mistake in the settings,...

Hi
This issues just started today. Start SDR Console 3.3 3195 (using Ham Radio Deluxe, VSP Mgr, Omni Rig, Yaesu 1200, SDRplay RSPdx) and it will randomly lock up. No movement on waterfall, can't change the radio freq via SDR Console, clicking the...

Hi Simon,
there are some waterfall differences between sdrconsole 3.2 and 3.3 version, viewing the same signal, using an RTL-SDR V3 dongle on USB, at 250 & 300 kHz bandwidth.
Some screen shots, with the same configurations

73 Rocco IK8XLD

HI,

I'm using Version 3.3, Build 3195 on Windows 11 and noticed the following reproducible two bugs:
After pressing the E2 button (Filter Low) on the ELAD TM-2 controller, the programm crashes (a message pop's up: please wait - but nothing happens)...

I have a Hermes-lite 2. If I activate the option Band voltage for the Hermes-lite 2 I ever get the same output voltage from the HL2, independ which frequency I select - no changes.
With other software (in this case Thetis) all is working correct,...

Hi,
so I went the cheap way, because this is what I could afford. I bought a clone RSP1A from Aliexpress.
It works fine with SDRConnect.
Does not start with SDRUno no matter which version, albeit it starts right after installation, but not if I...

External radio IF offset for different modes works at startup. But if the mode is changed while SDRconsole is running, the new offset is not updated/applied.
For example, if started in USB (SSB-U), the SSB-U offset is persistent for the entire...

Hello! I was having an issue with the cuda fft support where it seemed like the cuda driver would fail and the cpu driver would take over. This was noticeable because the waterfall noise floor would move faster in cpu mode, and the noise floor...

Hi All, I apologise if I don't provide too much info. Equipment: Pluto. I had SDR Console 3.2 + Virtual cable working with FT8, once installed 3.3 it stopped working. The WSJT was unable to activate TX correctly. If I increased audio level coming...

I've been having trouble with the mute either not working at all, or recovering too soon. I use SDR Console with a lower power boat anchor. It worked fine for hours and now won't mute the strong signal from my transmitter which is bleeding through...

Hi,

I have been having lockups using Build 3131 on 3 separate computers, one is a 9th Generation Intel Core i9 Processor i9-9880H, NVIDIA GeForce GTX 1650 and 2 are 12th Gen Intel(R) Core(TM) i7-12650H with Intel® UHD Graphics, and all have 64gb of...

Hello,
I am trying to launch the Server Manager on a fresh install. I am on build 2848 and had the same issue with the Release build.

When I click the button to launch I see the process start in Task Manager but the UI never launches.

Any ideas...

hello new here im having issues with the rtl-sdr v4 i just got home a fewdays ago all programs i try sdr#, sdr++ and sdr console shift the local fm stations for an example 106.3 is located at 56.3mhz sdr# had a shift frequency option wher i can...

Hello again! I have another report which happens occasionally when I have the SDR console unfocused and behind other windows, but not minimized. After some length of time (usually long) I return to the console and find that a lot of the widgets have...

Hello all!

Silent installation/automated deployment of the current SDR-Radio does not seem to be possible because it looks like that its installer always displays this info message:

vcredist.png

It happens even if the actual 64-bit vcredist...