It's all about the Software

Just installed the new release. The problem I have is Shaded will not stay enabled in the spectrum, after restart.
The odd thing is that when running on my laptop as a remote setup, this problem does not happen.

Philip G7JUR

Hello,

I've bough a HL2 but I face issue with SDRConsole regarding the output power.
Basicaly i can't have more than 3W of output but I got 5W using Quisk.

I've tried to understand why and inspected network packet between my computer and my HL2...

I have had a Hermes II for a week now and have settled upon SDR Console for it's front-end. I have configured a virtual audio cable, a virtual serial cable, etc. and am able to use SDR Console with fldigi and WSJT-X without issue.

However, when I...

Can anyone tell me what signal level to expect from the PSK beacon on QO100 via Pluto and SDRC?

At the moment mine seems quite low at -112dBm or S2 but listening via the batc Goonhilly sdr it is about s9+10db. I am using a 90cm dish and 0.1 lnb....

Good day....I have never been part of any forum, in the past 30 years..So If I make mistakes forgive me...
Any ways, my question is as follows.
-OS is Windows 10 latest build, as SDR Console also latest build.
-Radio Ettus N210.
As per usual doing a...

Hi,

Not important, but was playing around with the built in digital decoder.
Have the mode set to USB

Tried PSK (all of them) at:
1.838
3.580
7.040
10.141

and RTTY at:
3.590
7.043
10.143

Lots of digits appearing, but all gibberish.

Any...

Hi all,

Is there a way to activate/deactivate the Dither and Random functions for a HERMES board?
For the RX888 there are tick boxes, but for ANAN/HERMES I have not found anything comparable.
Maybe I have missed it?
If not, I guess I will add this...

Dear,

simple feature to add in the External Radio Options menu, submenu Transmit.
Please add next to the Mute Audio checkbox a additional feature that will add extra time when the TX is going back to RX. There is some delay and I get very bad...

SDRC is nearly the PERFECT program for working satellites. The only place it is lacking is when running an external radio, there is no provision for having the External Radio Transmitter and the Internal Radio Dongle Rx track when running...

Hi (Simon) and all!
The external radio in satellite tracking is working very good for FM satellites, I have done some QSOs with an IC-705 as TX rig. The possibility to adjust the frequency from the IC-705 is very good.
But, for transponder sats with...

Hi,
If the S3 is set with Bandwidth 24.576MHz and the Range Slider below is completly on the left side, the V3 produce images in the upper frequency range from the medium wave.

Regards
Fernando

Screenshot-2021-01-22-163443.jpg

Hi,

Since few days I have the S3 here. Now I have install following Bandpass and Highpass Filters. See below.
I have configure the Filters in both Software exactly the same, but the result is not the same.

Console V3 Filter config
V3 Filter...

Simon, as you requested in the Groups.IO forum:

Currently 20 degrees is the highest minimum elevation that can be selected for recording passes. A higher minimum elevation would be useful in several situations:

1. Low gain antennas or low...

I am wondering how probable is to get this feature.
I see in your plans that you have diversity support for multiple phase-coherent receivers, but what about RSPduo and stereo diversity in particular?
Unfortunately the SDRuno supports only Maximal...

What are you doing for CW? Apps?

Hello,
i suggest to make the polarity of the PTT input switchable.
So you can use a simple Pull-Up Resistor between RTS and CTS/DSR and you need only a external Key with 2 wires.

Tried it with an Resistor but get reverse Logic. (Must press my PTT...

Hi all,

I have a problem with SDR Console when I want to use my FT-817 or my FT-857 with external radio option. I receive the error message Port busy and/or offline . To cancel it and make the external radio working, I have to remove and reinsert...

So,

With luck I'll publish information about the SDR Console support for Red Pitaya/Stemlab. It does work as a transceiver thanks to the work of another team.

How can I accurately calibrate the S Meter?
Especially without a signal generator.
Thanks

Some of these features make me envious :).

Hi Simon,

Would you consider a slight (maybe not from a programming perspective) change that would allow something like what is below:

AM 0-529 KHz my value would be 1 KHz

AM 530-1710 KHz my value would be 10 KHz

AM 1720-30000 KHz my value would...

... the PSK-beacon presently struggles with some stability problems with direct correlation to the SDRC synchronisation function. Amsat knows the issue. Don't worry.
DC6NY

Hello & HNY to all

I had no problems installing and testing an ETTUS USRP-N200 with SDR console 3.0.26
using Win7/64 and latest UHD 4.0 hardware driver.

However unlike shown on a a picture from Simon my X310 with UBX160 is not found via SDR...

Greetings,

Trying to set up frequency databases for use with SDR Console 3.0.26 on my Windows 8.1 computer.

When I selected either the AM or FM user list, I receiver the error shown on the right hand side of the attachment.

Sorry for using screen...

Hello All

I -think- I'm consistently seeing a buggish interaction between SDRC (3.0.22) + WSJTX (2.1.2) + Omnirig (1.19)

whereby SDRC autonomously changes the rig from DATA/PKT to USB (Upper SB), FT817 w/FT817 rig selection

Steps :

1. start...