It's all about the Software

Ignore

Hello Community,
I am still on the way to switch from SDR Uno to SDR console because of connecting my FT 817 to sdr console.
In order to see how sdrc works I made a simple setup.
1. Rspdx on sdr uno
Signal generator set to -40,2dBm, cable and...

Hello,

Have been trying to fit some of CSVUserlistBrowser, and what I normally have showing in Console (when not using CSVULB) all on
my pc screen. Dragging an edge just cuts stuff off. Running W10.
A real battle.

I know that the screen...

Hi,
When editing a 46 Gb I/Q file (see I-Q file_editing-#1 ) to extract a 200 kHz wide full lenght portion, the size of resulting file is less than 100Mb and the file covers a few minutes only of the original file (see I-Q file_editing-#2 ).
Did I...

Hello,
after update from 3.0.26 to 3.0.27 I always get an error dialogue at startup of SDR Console.
Manual press of Start button in the home menu, starts the device.
Version 3.0.26 could start directly one of my 2 two devices connected per USB.
Both...

I downloaded the 3.0.26 version of the SDRConsole (v3) to update my 2.0.20.

All is running nice.

I wish to link the program to my Icom IC-7000 through the Omnirig 1.19 for freq CAT control.

Now my Omnirig are in well relations with MixW3, JTDX,...

I tried to schedule a recording.
I entered all the information, frequency, time, duration, audio format, etc.. But the OK button did not enable. So the schedule could not be saved.

Can you confirm that?

Thanks

Hi,

I looked at the Digital modes screen, and what I have, apparently,
is RTTY and the PSK ones, only.

Should there also be Sitor-B/Navtex ?

If not, any chance of including in the next rev(s), (with Acars too, perhaps) ?

Much thanks,
Bob...

Hi Simon,

If I take a screenshot with the Console (.27 3/24/21) on the second monitor it takes a screenshot of my main monitor. It never did that before.

Barry
WB2ZXJ

I recorded a .wav snippet from a playback of a larger recording while in Binaural SAM mode. When I listened to it, it played back in a slow manner. Not delayed, but like the recording was playing in half-speed so the voice came out real deep and...

When using the Receiver Noise Reduction NR3 my Transmit Audio is distorted. When I change to NR1 all is OK. I didn't think there should be a correlation between the receiver settings and the Transmitter functions.
73, Don

I like many others I guess, use Virtual Audio Cable (VAC) by Eugene (Evgenii) Muzychenko for piping audio to and from SDR Console and other pieces of software.
Well just recently it has stopped piping the audio. This may have happened when the PC...

Let me start off by saying that IMHO, SDR-Console is by FAR the most professional and most capable of all currently available software products specifically written for SDR's. In the beginning I was an avid user of SDR# but quickly and eagerly made...

Is it possible to Average/Integrate Spectrum buckets with Console? Air Spy has Astro Spy and other applications support averaging for a given sample count. Thanks and enjoy, John.

EDIT: I am running 3.0.27 Preliminary on an Air Spy. I tried...

Hi There, new user,
I have installed my rx888 mk2 and the dependency's I have no signal on receive on either the hf or the vhf antennas.
SDR console seems to see the rx888 mk2 I'm wondering if there's any other drivers or settings i may have...

Hi, all:

Does the Server Map show the SDRC servers that are online? I've never seen anything there, other than the list form.

I tried searching the board, but the search term server map only returns this...

Information

The following words in...

Hi,
Apologies in advance if this is a noob question.
I recently purchased a Pluto SDR and am trying to test it on a local FM radio station (104.7MHz).
I’ve changed the config of the SDR so it now operates from 70MHz to 6GHz, so it’s in range (set it...

Having problems with AM & SSB reception with an RSP-1a whenever I reduce the RF gain below 6: very distorted or no audio. It sounds just like a biasing problem with an op amp when the DC bias point shifts toward one of the supply rails. Everything...

New LAN-IQ Owner searching for SDR control software - SDR Console v3 appears to work and is promising. However install footprint seems huge (600+ Mb?) - Any way to determine minimum disk space & files needed for a single radio?

Thanks.

It would be very useful to be able to edit the entries set up in the scheduler. One may want to make small changes to when the recording starts and stops, recurrence etc. The option now is Copy , and consequently deleting the old entry after making...

Hi all,

I'm using .27 of the console. I would like to use the HF1 and HF2 inputs of the S3 for different antennas. How do I teach the scheduler? For example, he should switch the Asia antenna in the evening and the American antenna in the morning....

Simon,
Would it be possible to produce a piece of software that plots the radiation pattern of a yagi antenna.

Some thing like output 0-360 degrees in say 5 degree steps to the rotator, Then read the signal strength from the SDR in db and plot it...

Hello,
I know, that V2 is not supported anymore, but I am still very often using the old Data File Analyser, because there is a possibility to import or export TAGs. Few days ago, after a few weeks pause, I have noticed a problem with a TAG label...

73!
I want to use an laptop with windows XP :lol: and RTL-SDR RTL2832U USB doogle.
Please someone could send me a version 2.x that works with windows XP.

Tnx

IV3RCH Marco

Hi all,

I have a problem with frequency synchronization with SunSDR2PRO. Both SDR Console and EESDR are set to OmniRig. After switching on, the frequency is synchronized, but only once. The same configuration with the FLEX6500 works perfectly. Has...