It's all about the Software

I have a small linear for working base station.

My portable setup is now modular, based around a G90 and an RSPDxR2 SDR and Console 3.4 it works amazingly well all held together with Omnirig.

/P I'm out and about running from 1W to 10w in the...

Goodmorning everyone,
I have implemented a CAT control with ESP32 and Encoder for VFO setting.
Is there anyway to select a receiver that I have create in SDRC ?
With CAT command FA, FB, FC etc.. I can set the frequency but is not possible to Enable...

Hi,
I have an external radio Elecraft K3 and a SDR radio Perseus. It works fine until I change the band or the frequency. If I change it, the spectrum and waterfall stop working. It's just noise. To fix it, I have to turn the external radio off and...

Sorry if I might have gotten this wrong,
But I had the impression that console could be used to do soundcard I/Q Conversion and could do bi directional sync with Omnirig ..

Yet I am stuck on radio definitions ...

It seems I'm mistaken?

Is it possible ( pretty please) to add the facility to cycle through the filters with a MIDI device as defined in the current mode selection?

As I posted on the IO forum, I find the incremental change of 50hz much too low when in BFM mode.. what...

Just a quick note to say:
Thank you Mr Brown for the free software. I made a donation last year and have just done the same a week ago via your donations page. I must just say how much I appreciate the effort and hard work that has gone into SDR...

Hi ,

is there anything going on for the Red Pitaya 16 bit ?

Kind Regards

Pat

Attached to this post is a SDR Console XML file that turns a MIDI piano keyboard into an SDR Console controller. Two octave keyboards are plentiful and cheap, and some may be more durable than DJ Controllers. I've set up all of the usable receiver...

Sorry if this has been raised before.
I have a hard drive folder containing one set of chained recordings made by SDRC. They were found in an internet archive of HamSCI files.

The first 30 or so had been omitted, so the filename sequence begins...

As posted to the IO group a little while back, but putting it here in case it gets lost....

I have used the Memories a lot more recently, for example to put beacon frequencies in, or for using as a scratchpad during openings.

I find it's better...

Hello,
in the following groups.io discussion it was already asked about flip mode implementation for better rotor control.

I now wanted to put this feature request in the correct location.

The gist is as follows.

For rotors supporting 180° of...

Hi,

to my knowledge the actual Aaronia support is limited to the v6 full version , not the ECO. So I wonder if it is planned to support also the ECO, as this is for sure the radio that will be bought by many hobbyists.

I own the ECO in RX/TX...

SDR console is my favorite program for controlling SDRs, the latest addition is a ZynqSDR/LibreSDR which comes in a CNC housing. This SDR it is equivalent to the PlutoSDR, in fact the Pluto+ with 2TX and 2RX but it requires modified firmware. What...

Subject: Assistance with Ingesting Raw IQ Data from SDR Console across LAN into Python on another PC

Hi, I’m attempting to ingest raw IQ data output from either the Data Repeater or the SDR Server in SDR Console using Python. I can successfully...

The spectrum of a spyserver shows op with a peak carrier on any entered receive frequency and a valley around it.
On certain higher frequencies the whole display starts bouncing up and down.

When using the SDR# client all is fine.

You can try with...

Hello,

I have been running thetis with HL2, fully loaded, for a while now. It works great, band switching the XPA-125B and all, but I want to try SDR Console. I have a couple SDR dongles I want to add to this setup to make a sweet SDR rig. But...

Found information on this gem on radio reference a couple months ago. Am surprised not many folks have this. The waterfall display is what drove me to this. Was going to get a Chinese radio with a waterfall display but to many mixed reviews. Am glad...

Hi Simon:

I feel like I am asking for the moon to even ask for DX cluster spots to be added to the program. But is this possible, or no. This is the best world map I have ever seen for hams!

Thanks for creating this.

Scott N1IA

hello
will be great if you can add a SA44B — 4.4 GHz Spectrum Analyzer

do you thing it is possible
thanks
and by the way i love sdr console

Hi All

I am trying to find a way to solve an issue I am having,
My setup is a Adam Pluto Controlled by SDRconsole and I am running JTDX and JTsync on my PC
Now when I sync the time on the PC to the server I am seeing the FT8 stations have a dt...

Hi,

I'm about to buy an SDR, and I'm interested by the Pluto+.
But I also found other alternative like LibreSDR, which seem to be similar (but with a better FPGA), or even less known ones like the GeekRF One (and if you know others, don't hesitate...

A little wish, big effort? But asking anyway...

Hovering the mouse over spectrum or waterfall displays a vertical tuning bar with centre and bandwidth limits plus channelised tuned frequency.

An optional mode could be cross-hairs. Vertical to show...

Hello ...
I wonder how I can feed an I-Q stream from external source LIVE into SDR-Console for displaying ??

73 , Jens / HB9JOI

I've started my Christmas Present List early this year. The latest item is for any generous SDR software developers out there...

Similar to a list of markers to show on the spectrum display: this is a set of frequencies to *hide*  from the display,...

I have a user that probably doesn't know that one can use the pre-amp even with the AGC on.
It might be too late to train this person that you don't have to turn off the AGC to get a preamp on
for use when on 20m and higher.

I am forever finding...