It's all about the Software

Hi Simon,

Greetings from VK3

Been following your SDR Television development - great to see your beta release.

Unfortunately we don't have access to QO100 from VK - but we are active on the local ATV repeater which is VK3RTV.

We have a NET every...

Simon,

I have been eagerly awaiting the beta release of SDR TV and downloaded it today. My setup has the Pluto SDR connected on a separate network and is not directly connected via the USB port. The previous version of SDR Console was set up to...

I'm impressed with SDR-Television. I'm currently running it on an Intel NUC 8i7BEH with 32GB RAM and it runs ok at 333k, but could probably be better, so I'm considering buying a new PC specifically for SDR-Television. What is the ideal machine in a...

Sorry all,
So many questions.

I have noticed on higher frequencies the VCO from my TX Radio in this rig (my G90) is to the side of the listening frequency on 20m and up.
Tuning to a higher frequency is inaudible, however as you tune down the...

Goodmorning everyone,
I have implemented a CAT control with ESP32 and Encoder for VFO setting.
Is there anyway to select a receiver that I have create in SDRC ?
With CAT command FA, FB, FC etc.. I can set the frequency but is not possible to Enable...

Hi,
I have an external radio Elecraft K3 and a SDR radio Perseus. It works fine until I change the band or the frequency. If I change it, the spectrum and waterfall stop working. It's just noise. To fix it, I have to turn the external radio off and...

Sorry if I might have gotten this wrong,
But I had the impression that console could be used to do soundcard I/Q Conversion and could do bi directional sync with Omnirig ..

Yet I am stuck on radio definitions ...

It seems I'm mistaken?

Just a quick note to say:
Thank you Mr Brown for the free software. I made a donation last year and have just done the same a week ago via your donations page. I must just say how much I appreciate the effort and hard work that has gone into SDR...

Hi ,

is there anything going on for the Red Pitaya 16 bit ?

Kind Regards

Pat

Attached to this post is a SDR Console XML file that turns a MIDI piano keyboard into an SDR Console controller. Two octave keyboards are plentiful and cheap, and some may be more durable than DJ Controllers. I've set up all of the usable receiver...

Sorry if this has been raised before.
I have a hard drive folder containing one set of chained recordings made by SDRC. They were found in an internet archive of HamSCI files.

The first 30 or so had been omitted, so the filename sequence begins...

As posted to the IO group a little while back, but putting it here in case it gets lost....

I have used the Memories a lot more recently, for example to put beacon frequencies in, or for using as a scratchpad during openings.

I find it's better...

Hello,
in the following groups.io discussion it was already asked about flip mode implementation for better rotor control.

I now wanted to put this feature request in the correct location.

The gist is as follows.

For rotors supporting 180° of...

Hi,

to my knowledge the actual Aaronia support is limited to the v6 full version , not the ECO. So I wonder if it is planned to support also the ECO, as this is for sure the radio that will be bought by many hobbyists.

I own the ECO in RX/TX...

SDR console is my favorite program for controlling SDRs, the latest addition is a ZynqSDR/LibreSDR which comes in a CNC housing. This SDR it is equivalent to the PlutoSDR, in fact the Pluto+ with 2TX and 2RX but it requires modified firmware. What...

Subject: Assistance with Ingesting Raw IQ Data from SDR Console across LAN into Python on another PC

Hi, I’m attempting to ingest raw IQ data output from either the Data Repeater or the SDR Server in SDR Console using Python. I can successfully...

The spectrum of a spyserver shows op with a peak carrier on any entered receive frequency and a valley around it.
On certain higher frequencies the whole display starts bouncing up and down.

When using the SDR# client all is fine.

You can try with...

Hello,

I have been running thetis with HL2, fully loaded, for a while now. It works great, band switching the XPA-125B and all, but I want to try SDR Console. I have a couple SDR dongles I want to add to this setup to make a sweet SDR rig. But...

Found information on this gem on radio reference a couple months ago. Am surprised not many folks have this. The waterfall display is what drove me to this. Was going to get a Chinese radio with a waterfall display but to many mixed reviews. Am glad...

Hi Simon:

I feel like I am asking for the moon to even ask for DX cluster spots to be added to the program. But is this possible, or no. This is the best world map I have ever seen for hams!

Thanks for creating this.

Scott N1IA

hello
will be great if you can add a SA44B — 4.4 GHz Spectrum Analyzer

do you thing it is possible
thanks
and by the way i love sdr console

Hi All

I am trying to find a way to solve an issue I am having,
My setup is a Adam Pluto Controlled by SDRconsole and I am running JTDX and JTsync on my PC
Now when I sync the time on the PC to the server I am seeing the FT8 stations have a dt...

Hi,

I'm about to buy an SDR, and I'm interested by the Pluto+.
But I also found other alternative like LibreSDR, which seem to be similar (but with a better FPGA), or even less known ones like the GeekRF One (and if you know others, don't hesitate...

A little wish, big effort? But asking anyway...

Hovering the mouse over spectrum or waterfall displays a vertical tuning bar with centre and bandwidth limits plus channelised tuned frequency.

An optional mode could be cross-hairs. Vertical to show...

Hello ...
I wonder how I can feed an I-Q stream from external source LIVE into SDR-Console for displaying ??

73 , Jens / HB9JOI