It's all about the Software

I tried opening additional receiver windows to run different SDRs, but instead of additional windows opening, additional columns with different colors appeared on the same screen. Now, I can't seem to figure out how to close any of them or open...

Hi all
I need to re-install SDR Console on a new computer.
Is there a config file that I can transfer from one computer to the other so I do not have to spend hours reconfiguring ? If so, how is it named, and where is it located ?

TU + 73
Paul F6EXV

Hi Simon,

Greetings from VK3

Been following your SDR Television development - great to see your beta release.

Unfortunately we don't have access to QO100 from VK - but we are active on the local ATV repeater which is VK3RTV.

We have a NET every...

Would it be possible to add support for 2MS/s transmissions (repeater outputs) please?

very best regards,

Justin - G8YTZ

Solved: missing driver

Hi, Simon. I believe I've found a bug in SDRC's MIDI interface. Windows only allows one application to listen to a Midi controller. Which means that apps need to take into account that a controller might already be used by another app, and if so,...

Hi,

I installed SDR Television and I hooked up my Pluto SDR. I must be doing something wrong, because the program will not start. The Pluto can be found on COM3 I found out. No crashdump and no logfiles found.

I am using Windows 11 64 bit with an...

I'm converting my ham radio computer usage to include SDRC as either the main receiver or as a panadapter. My Icom 7300, the External Radio will always be my transmitter. I've run across a weird thing. When running JTDX or WSJT, if Tracking is...

I have a small linear for working base station.

My portable setup is now modular, based around a G90 and an RSPDxR2 SDR and Console 3.4 it works amazingly well all held together with Omnirig.

/P I'm out and about running from 1W to 10w in the...

Simon,

I have been eagerly awaiting the beta release of SDR TV and downloaded it today. My setup has the Pluto SDR connected on a separate network and is not directly connected via the USB port. The previous version of SDR Console was set up to...

I'm impressed with SDR-Television. I'm currently running it on an Intel NUC 8i7BEH with 32GB RAM and it runs ok at 333k, but could probably be better, so I'm considering buying a new PC specifically for SDR-Television. What is the ideal machine in a...

Oops, posted to wrong forum. Text moved to External Radio.

Hello,

Will blame the following most basic question
on old age now. Great excuse for most anything.

Could someone please give me the link to the latest
version I should download ? (any reason for a very basic contemplated user to download a Beta...

Sorry all,
So many questions.

I have noticed on higher frequencies the VCO from my TX Radio in this rig (my G90) is to the side of the listening frequency on 20m and up.
Tuning to a higher frequency is inaudible, however as you tune down the...

Is it possible ( pretty please) to add the facility to cycle through the filters with a MIDI device as defined in the current mode selection?

As I posted on the IO forum, I find the incremental change of 50hz much too low when in BFM mode.. what...

Squelch does not work on AM, I listen to the AIR band and AM/ SSB sql level does not work. Any Ideas or is there a fix for this.

Dear G4ELI,

I made a silly post a while back, and then I bought an SDRplay and SDRSwitch.

V3.4 saw the SDR and ...setup Omnirig....and my mind was blown about twenty minutes later as I pulled in tiny signals and ramped up DSP ...

This is the...

Hello:

First let me say this is an AWESOME piece of software. I have a question: is there a place where I can set the received CW to exactly match my Kenwood TS590SG? I see I can change the filtering of course. But can't see where I can change the...

Hello everyone,

we have finished building a nice VFO with ADF4351 board as shown in the photo.
Has anyone tried it in transmission?

We have 2 small spurious residues at -60 db generated above and below 1.8 Khz from the carrier.
They basically...

I have powerline arcing once the lines dry out, and it makes the lowbands nearly impossible to RX during the daytime. Actively chasing it down with my RDF loop antennas and have it narrowed down to my neighbors driveway where there are at least two...

Hi all
I have set up a server. When I log in to the server to listen, it may be a problem with the network speed. The waterfall chart often stops and then resumes in an instant, and the audio is the same. I have set the bandwidth to 30K. The...

Hello:

Perhaps it is just me, but I am having trouble figuring out how to keep the freq span in the display after zooming in. The default seems to be 0-100 khz. I've tried all kinds of things to keep the span coming up every time I go to that band,...

Hi All,
I have a request regarding CAT command to select a specific Receiver RX1,RX2,etc...
With FA command I able to set frequency *FA, FB,FC, etc ) but I can't enable a specific receiver.

I only see in MIDI configuration the possibility to select...

Goodmorning everyone,
I have implemented a CAT control with ESP32 and Encoder for VFO setting.
Is there anyway to select a receiver that I have create in SDRC ?
With CAT command FA, FB, FC etc.. I can set the frequency but is not possible to Enable...

Hi,
I have an external radio Elecraft K3 and a SDR radio Perseus. It works fine until I change the band or the frequency. If I change it, the spectrum and waterfall stop working. It's just noise. To fix it, I have to turn the external radio off and...