It's all about the Software

Hello,
About 5 years ago, I set up an FT-817 and an RTL-SDR with SDRC. It worked perfectly, sats were tracked, doppler was corrected, I found stations on the waterfall and just pressed PTT on the microphone to work them. Now, I'm trying to get back...

As posted to the IO group a little while back, but putting it here in case it gets lost....

I have used the Memories a lot more recently, for example to put beacon frequencies in, or for using as a scratchpad during openings.

I find it's better...

Hello,
I haven't used my Pluto D for two months, when I start the SDR console (3.4) I usually, but not always, get the display below. What can be the cause?
Conn.jpg
73 Detlev

This looks like a very interesting new SDR It would be nice if SDRC supported it in the future.

73
Roland

I have another post on the forum regarding the same issue, but specific to an IF frequency question. I'm confident that I am using the correct IF frequency and this question is more general. I'm experiencing extremely low voice volumes. The sound...

SDR Console version 3.3 build 3236.
I have a new Adlam Pluto just out of the box last week.
I am having problems with stopping and re-starting the Console.
On startup, Select Radio > Definitions > Search Pluto SDR
produces 3 instances. One with an...

Hello,
in the following groups.io discussion it was already asked about flip mode implementation for better rotor control.

I now wanted to put this feature request in the correct location.

The gist is as follows.

For rotors supporting 180° of...

While my RTL-SDR v4 is working in SDRSharp, SDR++ and SDRAngel, it fails to work in SDR Console. It simply does not show anything and when I hit stop, the proces locks up. Tried v3.3 and v3.4 Beta. What did I do wrong?

Log
SDR Console tmp.txt...

I have posted this message on the Kenwood 570 group on Facebook but I thought that I would do the same here as it may be a software rather than a hardware issue.

I'm attempting to set up a panadapter display using an RTL-SDR dongle and SDR...

Hi,
Apologies in advance if this is a noob question.
I recently purchased a Pluto SDR and am trying to test it on a local FM radio station (104.7MHz).
I’ve changed the config of the SDR so it now operates from 70MHz to 6GHz, so it’s in range (set it...

I'm new to using SDR radio / software. I recently purchased a HF+ Discovery, and running it with SDR Console (SDRC) v3.3 I recently downloaded.  It's working great, but how do I know if I'm leveraging the proprietary noise reduction algorithm...

how about feature that at the click of a button a text or xml file so that the whole configuration is easily attached to a post.

Thank you for reading this.

Amongst other thing, I use the software as panadapter, synched with my HF rig. The system works like a charm, but I find it annoying that any time I change band on the RTX, the amount of spectrum I see on the panadapter...

Hi,
when adding the IC-R8600 to SDR-console (v 3.4) I noticed that both converter selection and invert spectrum where enabled.

I disabled both before saving, but does the spectrum has to be inverted when using the R8600 or is this something which...

I think there is a problem with applying a frequency calibration correction with the SDR receiver (a Zyncsdr / Libresdr) listening to the 70cm band (433.5 to 434 MHz) while the signal comes from a QO100 downconverter running between 10489.500 MHz...

Hello folks,

Apologies in advance if this is a simple fix but I've failed to add an external radio to Console.

I have followed the instructions;

View-More Options-Enable External radio- Then restart.

Its the restart is where I have the...

I can’t get VarAC to transmit and receive using SDR Console, Virtual Audio Cables or Omnirig connecting to the Hermes lite. Vara HF, I’m not sure what it is doing? Anybody ever get VarAC to work with SDR Console into Hermes? Struggling. Thanks.

I have not been able to get the LimeRFE to work above 100 MHz with SDRConsole. What I have found is the logic levels on U9 (SW6_V2 & SW6_V3) are not correct at 222 MHz. As such it can not receive or transmit on J3 at 222 MHz. SW6_V2 has to be a 1...

SDRC v3.3

When rapidly changing frequencies, sometimes the external radio frequency does not get updated to match the SDR frequency. It usually tracks even when scrolling rapidly, but 5-10% of the time does not. The fix is simply to change...

Is there more information about MAP65 Support in newer SDRConsole beside of whats in the SDRConsole itself

To be able to use SDRConsole with MAP65 for X-Pol (H/V) antennas it need support of two coherent 96KHz I/Q streams coming from a Dual...

I just changed from ICOM 7300 to ICOM7610. On the 7300, I use a IF tapping card to get the signal to a RSP1B SDR, itself piloted by SDR Console and it works so well. On the 7610, I was hoping to use the IQ signal from ICOM that work with HDSDR but...

How can I use the Pluto Plus ethernet port with SDR console?

Hi,

to my knowledge the actual Aaronia support is limited to the v6 full version , not the ECO. So I wonder if it is planned to support also the ECO, as this is for sure the radio that will be bought by many hobbyists.

I own the ECO in RX/TX...

hello, i have a problem with sdr, namely when i connected a 3.5-52mhz longwire antenna, there appeared such dashed lines on the waterfall in sdr console v3.3, as if reflections of the broadcast station, rf gain is 29.7db
I have rtl sdr v4 Is there...

Being new to SDR is fun but has it downsides. I am using a Hermes lite 2 with SDR Console and have been able to receive well on 10, 15,17,20, and 40 meters. I am trying to transmit through a usb connected mic with no progress. I have tried to tune...