It's all about the Software

Hi

I am completely new to this forum, also to SDR Console.

I downloaded V3.3 and completed the installation. My HL2 was immediately recognised but on starting Console, no signals were received. Instead RF was immediately output on an unknown...

Does the checkbox in SDR console that enables the use of an external reference clock result in setting FPGA register 0x00CF(0) in v2.4 of the LimeSDR Mini? If not, what is the simplest way to have this register/bit set when using v2.4? Thanks for...

Greetings all @ SDR-Radio.
My request is for a pop-up Deviation Meter, similar to the pop-up signal strength meter.
It would need to be able to read up 100kHz deviation depending on what mode, eg NFM, WFM, BC-FM is in use.
I use your program along...

Hello OM's

I use the SDR-Console V3.3 and my Waterfall screen is very bad.
Is this a bug problem?

My colour is Warbler and the Shading ist by 50% ... this are my best uses.

73, Christian OE5HCE

I am trying to run 3 WSJT-X instances on 3 different bands fed by 3 RX channels defined in SDRC. I can get the 3 audio stream to the WSJT-X instances but when I set the band in one of the instances, all 3 instances change to that band. I am using DX...

Hello,
I've been using your software with my RadioBerry that has started to gain traction again and am curious. Is there any possibility for a release the includes a dark mode for the window colors? With the customization of the waterfall colors, a...

Greetings all,

I basically reimaged my system, finally, after I can't even begin to ponder how long. So a new SSD a new install, a new experience right? All goes well, at least I thought so until I go to install my favorite SDR app. It doesn't...

i attempted to connect to an ANAN-10E which has already been verified using linHPSDR. Result: Nothing found, sorry!

however, in the logfile, there appears a response when i lied to SDRC 3.0.26 and told it to look for a Hermes Lite.

Note the...

I am using and RSPDUO with the bandwidth set to 10MHZ. I have 3 receivers at the FT8 frequencies for 10M, 12M, and 15M. When I select the 15M receiver, the audio on the 10M receiver goes away. The greatest spread between the receivers with audio on...

Hello,

I am currently using the SDR Console v3.3 program, and I would like to view the frequency and level values within a specific frequency band. Specifically, I want to know if there is a feature that allows me to save the frequency and level...

Hello,
I miss a good noise blanker in SDRC. Regardless of the settings in SDRC, I don't see any effect at all of the current noise blanker. Thus I can't use SDRC during the summer months :( since I live in the country side with electric fences close...

Hello all. I'm hoping someone can point out what I'm missing/doing wrong. I have SDRuno V1.42 1710 installed, and it shows 3.15 API. Console is the latest Build, see pics below. SDR Console works with the radio, but it shows as unknown , and...

Hello to the group,

In transmit mode, no data ( power - swr - drv - vdd) except ALC in the transmit meter display.
Screenshot-2024-08-22-111012.jpeg

Thanks for reading !

Renauld ON4KVI

Hi,
I updated SDR Uno to V1.42 1710 on my PC and ran it up with my fully functioning RSP2 that had been running happily under SDR Console 3.1. No problem.
Then updated SDR Console to v3.3. Now the same RSP2 will not start.
SDR Console 3.3 works...

There is a pop-up window (via Ctrl key) for frequency input, but I cannot find a way to set the filter width in a similar way, instead of dragging the green lines with a mouse. Am I missing something, or there is indeed no way to change it manually...

I have been in the Ukrainian Armed Forces since May 2022; I joined the ranks voluntarily, to defend my country against the Russian invasion. (I did the same in 2014, was seriously wounded in August 2014, etc.) I have been doing some radio monitoring...

Hello, I have been experiencing this bug for a while but recently noticed that I can easily recreate it just by quickly switching back and forth between receivers. Here is what happens:

1. Create two or more virtual receivers (i usually have 3...

Hello all!

I am using SDR Radio with Ergo4 and my Elad S3. I've noticed that every time I switch bands in favorites the volume defaults to 50%. This means when I schedule recordings that require a different band and higher audio, the audio on the...

Hello!
I am looking for help, explanation, ideas for my situation..
I'm a SDR Console user from ver 3.0.26 (2020-12-14) and now I'm @ ver 3.3 build 3236 from (2024-02-05)

Strange things started a month ago - the program did not start (the frequency...

Kits
The kits are on the download page .

.
.
.

3D Waterfall
This is the main new feature. For more information and a couple of videos just click here .
Ribbon bar, View, Waterfall, 3D.
Requires Windows 10, DirectX 12.

Screenshot 3D...

The visual gain attenuation modifier, each time the sdr is powered on for the first time in the current sdr instance, applies additional visible and audible gain to the output which is reset when the menu to set the gain is accessed. By this, i do...

Hello, is it possible to receive DAB+ signal with SDR Console ?

The intermod on the RTL-SDRs is well documented and I was experiencing some on Friday evening. I scanned through 6m and was surprised to see a bunch of sideband convos. So I listened in and realized I was hear the 40m late net check ins. I know that...

Hi,
I use 2 screen on my PC and when I use SDR Console V. 3.3 the screens go blank either both or one and after a few seconds they come back on again.
When I am not using SDR console this does not happen. Has anybody had this issue too? The typed...

Hi,
I have had SDR Console (V3.2 build 2731) running happily with RSPdx for several months. A couple of weeks ago I unplugged the PC to move it. Now reconnected I find I have a problem. SDR Console runs happily and appears to be responding...