It's all about the Software

A little wish, big effort? But asking anyway...

Hovering the mouse over spectrum or waterfall displays a vertical tuning bar with centre and bandwidth limits plus channelised tuned frequency.

An optional mode could be cross-hairs. Vertical to show...

Hello,
I just received my LibreSDR and tested it with SDR Console Version 3.3 build 2848 Ethernet connection.
RX, works well without any problems.
TX, no signal out of the LibreSDR.
LibreSDR is booting from SD-card (SD-card JT 2024 02 03)...

Hi,
i cannot use my LNB which has big drifts during daylight (over 100KHz) because the geostationary window span frequency is too small. I cannot zoom out and select the beacon to start correct tracking.

It would be nice to be possible to zoom out...

can someone please help? sdr console finds rtl dongle but i have no signal,
in the select radio box under option it says tuner : unknown,
on the pc in the house everything works fine and under option in the select radio it says tuner: rafael micro...

I have a problem, SDR Console freezes, mostly when I use the satellite function.
You can still hear the sound, but the interface freezes completely and there is no error message.
I have to close the program using the task manager.
I have already...

Hello ...
I wonder how I can feed an I-Q stream from external source LIVE into SDR-Console for displaying ??

73 , Jens / HB9JOI

Hi,

I'm developing a device to remote control the console and I observed an anomally with the MD command using the Serial port (CAT) connection.

As the documentation say (

MD
Mode
Read: MD; returns the current mode.
Write MD ;
Note: the mode...

I've started my Christmas Present List early this year. The latest item is for any generous SDR software developers out there...

Similar to a list of markers to show on the spectrum display: this is a set of frequencies to *hide*  from the display,...

Hi All...

I'm fortunate enough to be picking up an FDM-S3 later today but, as a non-ham with little or no electronics experience I really need some advice as to which power supply to purchase to get up and running.

I'll only need it for the S3 for...

Hej!

The Output power slider shows values ​​between 0 and 100%. unfortunately this regulator is not linear with the output power. Is it possible to linearize this or even calibrate it in dBm or W?

73, Holger DG3FEH

hello, I installed yesterday sdr console in my laptop
everything works ok ,but I have a problem , that I had never befor:
every signal I hear and see in waterfall has a shadow on the same frequency, but its only optical,the stations they are sending...

I have a user that probably doesn't know that one can use the pre-amp even with the AGC on.
It might be too late to train this person that you don't have to turn off the AGC to get a preamp on
for use when on 20m and higher.

I am forever finding...

Hi, new on this forum.
I use HL2 with all softwares like Thetis Sparksdr and Quisk, but with SDR console V3.2 or 3.3 the output power is around 0.5 W when speaking in the mic ( drive , proc & gain 100%) - Tune or whistle gives around 4 W a little...

hello, I have a small problem on a friend's SRD server, the server starts fine, it is visible on the monitor, port 50101 in TCP is open, the port forwarding in the box is OK, the parser -feu is OK, and from home I connect to his server without...

Is thera any change impelement TCI Protocol for CAT. TS2000 with Omnirig is one kind of pain if you use up / down converter, example LOG4OM cant go QO100 frequencies, its show offliine.
If you go under 2ghz its start show freq. As far i know,...

Hallo SDR-Console Users,

I use the SDR-Console V3.3 and an IC 9700 70cm + Transverter for Uplink. The frequency the console sends to my IC-9700 is 500 KHz to high on all Frequencys in the ssb part of the q100.
Changing the tx up frequency in the...

Hi All, I use SDR Console and SDR plays duo's (by 3). I also use Icom RSBA-1 software to remotely access my IC-7300.
As my ISP uses GCNAT (all my connections are 5G) I created a VLAN using Tailscale to provide me easy access to my remote radio....

Hi

I am completely new to this forum, also to SDR Console.

I downloaded V3.3 and completed the installation. My HL2 was immediately recognised but on starting Console, no signals were received. Instead RF was immediately output on an unknown...

Currently, sample rates for the HF+ Discovery are limited to a range of 192 to 912 kHz.
Occasionally, hunting for weak signals, a very low value (e.g. 32 kHz) can be useful.
Would anyone else be interested in this addition?

Does the checkbox in SDR console that enables the use of an external reference clock result in setting FPGA register 0x00CF(0) in v2.4 of the LimeSDR Mini? If not, what is the simplest way to have this register/bit set when using v2.4? Thanks for...

Greetings all @ SDR-Radio.
My request is for a pop-up Deviation Meter, similar to the pop-up signal strength meter.
It would need to be able to read up 100kHz deviation depending on what mode, eg NFM, WFM, BC-FM is in use.
I use your program along...

Greetings All
Two questions on the audio spectrum screen...
1) Is there anyway to get rid of the coloured fill to leave just the bare spectrum analyser trace ?
2) Is there anyway to change the vertical scale to bring the trace more in line with the...

Hello OM's

I use the SDR-Console V3.3 and my Waterfall screen is very bad.
Is this a bug problem?

My colour is Warbler and the Shading ist by 50% ... this are my best uses.

73, Christian OE5HCE

I am trying to run 3 WSJT-X instances on 3 different bands fed by 3 RX channels defined in SDRC. I can get the 3 audio stream to the WSJT-X instances but when I set the band in one of the instances, all 3 instances change to that band. I am using DX...

Hello,
I've been using your software with my RadioBerry that has started to gain traction again and am curious. Is there any possibility for a release the includes a dark mode for the window colors? With the customization of the waterfall colors, a...