It's all about the Software

Hello:

First let me say this is an AWESOME piece of software. I have a question: is there a place where I can set the received CW to exactly match my Kenwood TS590SG? I see I can change the filtering of course. But can't see where I can change the...

Hello everyone,

we have finished building a nice VFO with ADF4351 board as shown in the photo.
Has anyone tried it in transmission?

We have 2 small spurious residues at -60 db generated above and below 1.8 Khz from the carrier.
They basically...

Dear G4ELI,

I made a silly post a while back, and then I bought an SDRplay and SDRSwitch.

V3.4 saw the SDR and ...setup Omnirig....and my mind was blown about twenty minutes later as I pulled in tiny signals and ramped up DSP ...

This is the...

I have powerline arcing once the lines dry out, and it makes the lowbands nearly impossible to RX during the daytime. Actively chasing it down with my RDF loop antennas and have it narrowed down to my neighbors driveway where there are at least two...

Hi all
I have set up a server. When I log in to the server to listen, it may be a problem with the network speed. The waterfall chart often stops and then resumes in an instant, and the audio is the same. I have set the bandwidth to 30K. The...

Hello:

Perhaps it is just me, but I am having trouble figuring out how to keep the freq span in the display after zooming in. The default seems to be 0-100 khz. I've tried all kinds of things to keep the span coming up every time I go to that band,...

Hi All,
I have a request regarding CAT command to select a specific Receiver RX1,RX2,etc...
With FA command I able to set frequency *FA, FB,FC, etc ) but I can't enable a specific receiver.

I only see in MIDI configuration the possibility to select...

Goodmorning everyone,
I have implemented a CAT control with ESP32 and Encoder for VFO setting.
Is there anyway to select a receiver that I have create in SDRC ?
With CAT command FA, FB, FC etc.. I can set the frequency but is not possible to Enable...

Hi,
I have an external radio Elecraft K3 and a SDR radio Perseus. It works fine until I change the band or the frequency. If I change it, the spectrum and waterfall stop working. It's just noise. To fix it, I have to turn the external radio off and...

Tried all the download links at SDRRADIO.com today, but never was able to get anything but other unwanted software. Anyone have a link that really works??

73, K8AC

Hi All,
maybe I am doing something wrong but the tuner is not stored when I create Favourites?
I setup and stored Tuner A for 367.080MHz that is connected to my PTRX-9700 for 1296Mhz and via MAP65 setup to QMAP/MAP65
I setup and stored Tuner B for...

Hi all,

I'm one of those intuitive techy autistic types.

I want to use SDR Console with Omnirig and Soundcard from IF / IQ on the Xeigu I use in my portable setup.

HDSDR is OK ...I have it setup perfectly, but Console looks great!

Would like...

Sorry if I might have gotten this wrong,
But I had the impression that console could be used to do soundcard I/Q Conversion and could do bi directional sync with Omnirig ..

Yet I am stuck on radio definitions ...

It seems I'm mistaken?

Hi! Is it possible with SDR Console 3.3. to scan a range of frequency from....to....? Thank you

Hi everyone new to the site here i have installed the sdr server in the sdr console part of the program but it keeps timing out at 2 seconds after i go through the setup procedure. Radio is actively hookup My radio shows up in the list of sdrs to...

Are there any plans for SDR Console to work with the AOR AR5700D?

AR5700D.png

Hello everyone.
What is the procedure for adding provisional TLEs for a new satellite not yet referenced on Celestrak?
I'm using SDR Console v3.4.
Thank you in advance.

Pascal - F4IKX

SYMPTOMS
1. When SDR Console window remains minimized, the memory usage continuously increases. It can reach insane levels of memory usage until the application can stop responding or crashes.
2. Restoring the window causes very high disk activity...

I have a good signal on my FM station, but I am experiencing hissing noise in the background.

Is there anyway I can remove the noise. I have tried the noise filters, but it doesn't seem to make any difference.

Thanks in advance for your help.

Hi all
Just joined the forum !
Using SDR Console version 3.4, and trying to configure it to do FT8 with MSHV.
When I set line 1 for transmit and for receive, the Pluto will go transmit erractically (with MSHV not opened). Bursts of emissions,...

Is it possible ( pretty please) to add the facility to cycle through the filters with a MIDI device as defined in the current mode selection?

As I posted on the IO forum, I find the incremental change of 50hz much too low when in BFM mode.. what...

Thought I'd take this off the io.Groups to save clogging it up.

So, in recent weeks I began to have issues with my i9-13900 system first failing with Windows Update, then random software crashes, and a failure to repair or reinstall Windows 11....

hello, I have a small problem on a friend's SRD server, the server starts fine, it is visible on the monitor, port 50101 in TCP is open, the port forwarding in the box is OK, the parser -feu is OK, and from home I connect to his server without...

Using Windows 10/11, the WINGET utility identifies the SDR Console (V3) version as Unknown .

>winget list SDR-Radio.com (V3)
Name Id Version Available Source
----------------------------------------------------------------
SDR-Radio.com (V3)...

Hello Friends,

Anyone of you use the card like this SDR 70 MHz-6 GHz Zynq7010+AD9363 with the SDR- Console software ?

Is it possible to manage the 2 RTX channels independently ?

I would like to use it as an RTX driver for an HF radio with IF at...