It's all about the Software

I am using the latest version of Console with an Airspy HF Discovery, bandwidth set at 912kHz. I would like to make IQ recordings of the entire MW band from 530kHz to 1710kHz. I tried using the MW settings in Favourites but the resulting recordings...

Hi all,

Is it possible to override the built-in 200 Hz high pass filter when using narrow FM? Although the majority of voice intelligibility is probably above this, I would very much prefer to adjust this and bring some of the lower frequencies...

I'm running 3.3 build 2870, when I change bands using favourites the Rx audio changess to the default windows audio device. Could we have it retain the last used setting please.

Thanks

Phil VK7ZPD.

Hi,

I am temporarily using an RTL-SDR V3 dongle while learning about SDRC. It basically works but the external receiver window always shows Port Busy. Is this a problem? The radio is a Kenwood TS-590S and the software is DXLab. I am using the basic...

I was not satisfied with the Noise Reduction and Noise Blanking Performance of the ICOM-7300. The Noise Reduction and Noise Blanking performace of SDRSharp impressed me (thanks Joanne).

The IC-7300 has a USB IF output where the the IQ Output as...

I am new to HL2
The first board did not work and I ordered another.
I tested now with new board and have no output when tuning.
OP power set to 8 for not getting again a defective output
So finaly I tested with straight key.
I have 2 watts output...

SDR Console v3.2 for Windows 7 is locked by default

How to unlock it ?

Hovering over Program lock icon I get lock locked
When I click Program lock, new window opens with a message: Program locked
and Open lock icon to click
to unlock the Program...

How to upload screenshot of my SDR Console v3.2 ?

works for url address

(1) I will supply screenshots if needed, just tell me what to provide.

I used win7 for the longest time. Everything worked fine. I had to replace my pc and it came with win11 installed. I am new to win11.
Here is my issue: Radio on, SDR console...

Hello - I'm trying to understand how to set up SDR-Console's satellite tool to automatically record satellite I/Q data based on the schedule. I can't quite figure out how to set up and enable automatic recording. I opened the Automatic Scheduler...

Hello,
I want to record more than one audio stream within 500khz of bandwidth with only one SDR. I am trying to record NFM Local EMS and NFM Local LEO. Is this possible.
If I use data recording it has too much dead space and takes up to much...

SDR Console v.3.2 32-bit installed, Media-Tech usb RTL dongle installed, recognized, no signal at all (Windows 7)

Is there any way to check if any signal is received ?

RTL Dongle USB - unknown 20 -2000Mhz (drivers installed)

dBm meter set at...

The day before yesterday i received a handheld personnel Dosimeter , brand new and a weeks wait off the bay .

14 day battery life with screen and alarms off , rechargeable .

After setting it all up i hung it on the wall off a self tapper turned on...

Downloaded Zadig as advised, run in Windows 7, 32-bit
to update driver and Total Security 360 monitored 2 problems
and win usb driver update locked

I can attach photo.

thank you

darius

Media-Tech USB RTL dongle installed, recognized, no signal at all

any idea ?

small indoor antenna installed by default
no signal at all

RTL usb dongle donated by my friend
since another Media Tech usb dongle purchased a week ago was to short to...

SDR Console v.3.2 32-bit installed, Media-Tech usb RTL dongle installed, recognized, no signal at all (Windows 7)

Is there any way to check if any signal is received ?

RTL Dongle USB - unknown 20 -2000Mhz (drivers installed)

dBm meter set at...

I have upgraded status of your mail from spam to not spam with Gmail

(forum registration confirmation email received by Gmail)

im using a RTL SDR v3 , this happens when i use the right button of my mouse to move around the frequency or when i click on the center button, and no, this is not a dc spike, this thing its jumping .

Would a Propagation topic be useful for HF ?, or propagation results , or what is that shown on the sdrc screen .

Like for instance in the picture , see all those horizontal lines going up and down in frequency (mostly down) in the waterfall , the...

Copied pasted from HL2 Facebook group:
Jim Ahlstrom (designer of the filter board) has designed a general I/O board for the HL2. It allows things like amplifier/transverter interfacing, PureSignal input, dedicated receiver input and a few other...

This evening I wanted to record a few hours of LRA36 on 15476, so I pointed SDR Console 3.2 at my Airspy, set the bandwidth to 192 kHz, and started recording. Reception was very good for the first hour and a half, then started to fade. After 3 hours...

Hello!
I have a little problem SDR Console 3.2 and above Server not send data to client using RX-888 mk II
I have a computer. To this computer connect a few receivers. On this computer running SDR Console Server. On other computer running SDR...

Hi,

Hi, I use SDR Console as panadapter for IF K3+FCD+. Working fine but randomly accidentally stops meter to show a real value. After some time he shows again. This is repeated accidentally. Screenshot-2023-03-07-193823.jpeg

Dear,

A setup is made with an AOR-AR8600 with 10.7MHz IF Out connected to an RTL-SDR.
The AR8600 is setup as external radio with Rigctl
The RTL-SDR is radio 1
In External Radio options, SDR frequency selection, the IF output with an offset of...

Hello
I'm having problems with my new windows 10 computer.
the sdr console frequency is fixed and cannot be changed, I can punch in new frequency but the spectrum stay's the same .
I can zoom in and tune in to stations on the frequency span that the...