It's all about the Software

Had a bad case of Sciurus carolinensis or Tamiasciurus hudsonicus!
Grey squirrel or Red squirrel decided to chew on the insulation, and wires of the antenna about 4' from the 9:1 unun. Both ends were stripped about 2 so I wrapped the two back...

Hi
I hope you forgive my ignorance.
To use SDR console on a Windows PC to control a raspberry pi 4 with 1 RTL-sdr dongle, what do I need to install in the raspberry (drivers, software, etc.) ?
Many thanks in advance
Regards

Hi,

I am trying to interface the SDR Console V3.3 with Log4OM2.

I am not succeeding to get the VFO & mode information to the Log4OM2 application.

Log4OM2 works fine with my FT991A.

An suggestions as to how to get this fixed?

Thanks
Ravi

Hi,

On SDR-Console V 3.3 when I try to select Hermes Lite 2 in the Search option, I am given the below option

-> Default
-> Extended
-> Fixed Address

But when I select the option of PlutoSDR in the search option,I do not find any of the options...

SDR Console has been working flawlessly until today when a Windows update installed. Now SDR Console will run only a minute or two then freezes, accompanied by the disconnect sound ding. I can click on the stop button, wait a minute or so, then...

Hello,
I am using sdrconsole for the QO100 operation successfully.
I have linked my external radio and the SDR console shares the frequency information on 70cm to my rig.
On the SDR display I see the 10.489 frequency as it is used on the satellite....

So when I reboot the PC that the server is installed on, the system status comes up on-air-services unknown
To get things to work I have to stop the service in the server manager and then restart, and then everything works fine.
Now if I reboot...

zoom function with external radio doesn't work in the right way, the signal move from the tuned frequency. changing zoom an offset on the sdr tuning about 1 kHz is applied.

In addition moving radio vfo change the zoom on the spectrum.

Tracking in...

So gentlemen,
I can not find an answer in FAQ's on this issue, so I would like to ask the many users with far more knowledgeable and experience with SDR Console a seemingly simple question.
With both a CW Transmit mode and the ability to generate...

I have been figuratively banging my head against the wall trying to find software that lets my Hack RF One transmit. This SDR console looks promising but I can't seem to get the Transmit option to work. Receive works fine.

I am really hoping...

I'm observing SDRC crashing when using 8 MHz bandwidth. This has been a long running problem I've never reported because I seldom use more than 2 MHz of bandwidth and the crashing at 8 MHz of bandwidth is at random times.

Though there may be a...

I'm an old timer of 45 years on amateur radio so this stuff is new to me. I would like to know what I need to get my Kenwood TS-59SG and HackRF One SDR to work to decode FT8 and display the FT8 also what other software is needed to work FT8 on the...

Hi, first of all,sorry didnt read the whole forum!
Is it possible to implement Flrig for controlling external radio.
Im switching from Port cloning and using hrd and omnirig to flrig.
But now not possible to change frequency by clicking waterfall...

I use SDRConsole for preferance with my SDRPlay DX but have recently bought the remarkable BELKA all mode RX for mobile SWLing. It provides an IQ output for use via a computer sound card and together with a laptop, would be very useable. For...

Can somebody kindly provide me with detailed instructions on how to allow SDR Console to recognize a B210. Please assume that all what is available on this site has been done without success. Downloading drivers from ettus is part of it.
Thanks...

Something is wrong with Super Station #1, all signals are down by +20dB. Will have to walk out and check the antenna. We had horrendous winds for two days, and may be laying of ground or in pieces. Was too dark to investigate when I discovered it...

Just noticed this error(?). When selecting Pre-Amp on/off a window pops up saying the AGC must be off? Pre-amp works just fine on or off with AGC on.
Just uploaded the latest, V3.3 build 3236 on a W10 laptop
See screenshot

73 Kriss KA1GJU

When CW mode active, a means to park the peak of the CW signal in the middle of the filter window, like many HF transceiver's can do. I think it's essentially a search for peak signal strength +/- from the current VFO.

Also the ability to choose CW...

Hi,
I have Sdr-console on my pc.
I would like to copy all settings/data (memories etc) to my laptop.
Purpose is to take my laptop, radio, antennas when I am camping to 'listen around'.
Is that possible?
How can I do that?
Thanks in advance.
Paul

Hello,

I'm having an External Radio Error During program Launch with the current and last few Beta versions. I'm using a TS-590SG with SDRPlay's RSP1a SDR and OmniRig. During SDR Console program startup there is a really long delay before the the...

SDRConsole has now become my fav SDR software, and I keep finding more and more wonderful and powerful features.

If I could make one request... That would be a configurable RX window (?) Tile (?) that can float, rather than the current offering....

Support in the way of a macro-editor for automating SDRConsole.
Specifically, being able to map a key combo triggered by an external keypad (could be connected via USB, might be Bluetooth) input to the program, and have it kick off one or more...

Hi,

SDR Console 3.3 / Pluto Plus / CN-0417 Preamp / DX Patrol 12w Amp.

When I first power up the Pluto+ and run SDR Console I can’t get any TX power out on voice or tone. The TX button in SDRC changes colour and I am showing a modulated signal or...

Hi all, is it possible to have 2 identities on start up. One for hf and one for qo100? I tried this but when I switched to HF console still shows qo100 settings and visa versa.
I'm probably missing something obvious.
Regards Brent G5TV

Good morning. I would like to know if compatibility with the new SDRPLAY RSP1B will be added to the SDRConsole in the future. Thank you, kind regards to everyone