It's all about the Software

I searched the forum with no results. Can SDR Sharp control this device? I would like to use it as a classic SDR receiver with software other than Expert Electronics. Thank you for the information.

I am using the latest version of Console with an Airspy HF Discovery, bandwidth set at 912kHz. I would like to make IQ recordings of the entire MW band from 530kHz to 1710kHz. I tried using the MW settings in Favourites but the resulting recordings...

I was not satisfied with the Noise Reduction and Noise Blanking Performance of the ICOM-7300. The Noise Reduction and Noise Blanking performace of SDRSharp impressed me (thanks Joanne).

The IC-7300 has a USB IF output where the the IQ Output as...

Hi all,

Is it possible to override the built-in 200 Hz high pass filter when using narrow FM? Although the majority of voice intelligibility is probably above this, I would very much prefer to adjust this and bring some of the lower frequencies...

I'm running 3.3 build 2870, when I change bands using favourites the Rx audio changess to the default windows audio device. Could we have it retain the last used setting please.

Thanks

Phil VK7ZPD.

Hi,

I am temporarily using an RTL-SDR V3 dongle while learning about SDRC. It basically works but the external receiver window always shows Port Busy. Is this a problem? The radio is a Kenwood TS-590S and the software is DXLab. I am using the basic...

I am new to HL2
The first board did not work and I ordered another.
I tested now with new board and have no output when tuning.
OP power set to 8 for not getting again a defective output
So finaly I tested with straight key.
I have 2 watts output...

SDR Console v3.2 for Windows 7 is locked by default

How to unlock it ?

Hovering over Program lock icon I get lock locked
When I click Program lock, new window opens with a message: Program locked
and Open lock icon to click
to unlock the Program...

How to upload screenshot of my SDR Console v3.2 ?

works for url address

(1) I will supply screenshots if needed, just tell me what to provide.

I used win7 for the longest time. Everything worked fine. I had to replace my pc and it came with win11 installed. I am new to win11.
Here is my issue: Radio on, SDR console...

Hello - I'm trying to understand how to set up SDR-Console's satellite tool to automatically record satellite I/Q data based on the schedule. I can't quite figure out how to set up and enable automatic recording. I opened the Automatic Scheduler...

Hello,
I want to record more than one audio stream within 500khz of bandwidth with only one SDR. I am trying to record NFM Local EMS and NFM Local LEO. Is this possible.
If I use data recording it has too much dead space and takes up to much...

SDR Console v.3.2 32-bit installed, Media-Tech usb RTL dongle installed, recognized, no signal at all (Windows 7)

Is there any way to check if any signal is received ?

RTL Dongle USB - unknown 20 -2000Mhz (drivers installed)

dBm meter set at...

The day before yesterday i received a handheld personnel Dosimeter , brand new and a weeks wait off the bay .

14 day battery life with screen and alarms off , rechargeable .

After setting it all up i hung it on the wall off a self tapper turned on...

Downloaded Zadig as advised, run in Windows 7, 32-bit
to update driver and Total Security 360 monitored 2 problems
and win usb driver update locked

I can attach photo.

thank you

darius

Media-Tech USB RTL dongle installed, recognized, no signal at all

any idea ?

small indoor antenna installed by default
no signal at all

RTL usb dongle donated by my friend
since another Media Tech usb dongle purchased a week ago was to short to...

SDR Console v.3.2 32-bit installed, Media-Tech usb RTL dongle installed, recognized, no signal at all (Windows 7)

Is there any way to check if any signal is received ?

RTL Dongle USB - unknown 20 -2000Mhz (drivers installed)

dBm meter set at...

I have upgraded status of your mail from spam to not spam with Gmail

(forum registration confirmation email received by Gmail)

im using a RTL SDR v3 , this happens when i use the right button of my mouse to move around the frequency or when i click on the center button, and no, this is not a dc spike, this thing its jumping .

Would a Propagation topic be useful for HF ?, or propagation results , or what is that shown on the sdrc screen .

Like for instance in the picture , see all those horizontal lines going up and down in frequency (mostly down) in the waterfall , the...

Copied pasted from HL2 Facebook group:
Jim Ahlstrom (designer of the filter board) has designed a general I/O board for the HL2. It allows things like amplifier/transverter interfacing, PureSignal input, dedicated receiver input and a few other...

This evening I wanted to record a few hours of LRA36 on 15476, so I pointed SDR Console 3.2 at my Airspy, set the bandwidth to 192 kHz, and started recording. Reception was very good for the first hour and a half, then started to fade. After 3 hours...

Hello!
I have a little problem SDR Console 3.2 and above Server not send data to client using RX-888 mk II
I have a computer. To this computer connect a few receivers. On this computer running SDR Console Server. On other computer running SDR...

Hi,

Hi, I use SDR Console as panadapter for IF K3+FCD+. Working fine but randomly accidentally stops meter to show a real value. After some time he shows again. This is repeated accidentally. Screenshot-2023-03-07-193823.jpeg

Dear,

A setup is made with an AOR-AR8600 with 10.7MHz IF Out connected to an RTL-SDR.
The AR8600 is setup as external radio with Rigctl
The RTL-SDR is radio 1
In External Radio options, SDR frequency selection, the IF output with an offset of...