It's all about the Software

Hi all
Just joined the forum !
Using SDR Console version 3.4, and trying to configure it to do FT8 with MSHV.
When I set line 1 for transmit and for receive, the Pluto will go transmit erractically (with MSHV not opened). Bursts of emissions,...

Hi ,

is there anything going on for the Red Pitaya 16 bit ?

Kind Regards

Pat

Attached to this post is a SDR Console XML file that turns a MIDI piano keyboard into an SDR Console controller. Two octave keyboards are plentiful and cheap, and some may be more durable than DJ Controllers. I've set up all of the usable receiver...

High winds severed the fiber optic cable up on the pole next to the building somehow. No evidence of tree limbs, so maybe whipping in the wind led to it's demise?
The ISP is supposed to arrive on the 11th, but not holding my breath due to previous...

Hi, I use a Transfox SDR by Sigfox, but it is not supported by SDRC. What can I do ?. Tks

OK, spent some time this AM doing A/B tests using the Nooelect Flamingo AM BC Filter.
The setup is:
Inverted L antenna, active 4 port multicoupler, two Airspy units with same firmware, two copies of SDRC running side by side. The copy on the left...

How can I use the Pluto Plus ethernet port with SDR console?

Does SDRConsole allow for Trunked signals or if not compatible with plugins like SDRTrunk or DSC+?

Hi. New user to SDR Console, but liking what i'm seeing thus far. That said, i've run into a very odd behavior using SDR Console 3.3 on a Windows 10 laptop with my Afedri-LAN (connected via ethernet). For the life of me, I cannot get intelligible...

In an effort to keep a daytime, 5KW AM radio station on 1540kHz 5.1miles (8.2km) away from me appearing in numerous locations in the upper bands, I thought I would give the Nooelec Flamingo AM BC filter a try. Thinking all my SDR's at three entirely...

I have been testing a Wellgood Loop Antenna with an RX-888 MKII. I've been getting impressive results, especially around 5 MHz for the UK Aero Volmets where there is a low noise floor.

But I have a huge noise jump from around 8.5 MHz to 12 MHz...

SDR Console version 3.4 build 3569

1，When recording data, the frequency in the file name is inconsistent with the actual frequency. I think it is correct to use the current actual received frequency as the file name. In addition, after changing the...

While my RTL-SDR v4 is working in SDRSharp, SDR++ and SDRAngel, it fails to work in SDR Console. It simply does not show anything and when I hit stop, the proces locks up. Tried v3.3 and v3.4 Beta. What did I do wrong?

Log
SDR Console tmp.txt...

Sorry if this has been raised before.
I have a hard drive folder containing one set of chained recordings made by SDRC. They were found in an internet archive of HamSCI files.

The first 30 or so had been omitted, so the filename sequence begins...

How to turn off?

I really did search all the menus and this forum but could not find a way to not show them.

Whit

While investigating the QRM generated by a local AM BC station that jumps to 5KW at local sunrise, I found the following action with the Radio Airspy Discovery using my
normal settings of:
AGC High (or low) doesn't matter
Attenuator OFF
Pre Amp OFF...

Hello,
About 5 years ago, I set up an FT-817 and an RTL-SDR with SDRC. It worked perfectly, sats were tracked, doppler was corrected, I found stations on the waterfall and just pressed PTT on the microphone to work them. Now, I'm trying to get back...

As posted to the IO group a little while back, but putting it here in case it gets lost....

I have used the Memories a lot more recently, for example to put beacon frequencies in, or for using as a scratchpad during openings.

I find it's better...

Hello,
I haven't used my Pluto D for two months, when I start the SDR console (3.4) I usually, but not always, get the display below. What can be the cause?
Conn.jpg
73 Detlev

This looks like a very interesting new SDR It would be nice if SDRC supported it in the future.

73
Roland

I have another post on the forum regarding the same issue, but specific to an IF frequency question. I'm confident that I am using the correct IF frequency and this question is more general. I'm experiencing extremely low voice volumes. The sound...

SDR Console version 3.3 build 3236.
I have a new Adlam Pluto just out of the box last week.
I am having problems with stopping and re-starting the Console.
On startup, Select Radio > Definitions > Search Pluto SDR
produces 3 instances. One with an...

Hello,
in the following groups.io discussion it was already asked about flip mode implementation for better rotor control.

I now wanted to put this feature request in the correct location.

The gist is as follows.

For rotors supporting 180° of...

I have posted this message on the Kenwood 570 group on Facebook but I thought that I would do the same here as it may be a software rather than a hardware issue.

I'm attempting to set up a panadapter display using an RTL-SDR dongle and SDR...

Hi,
Apologies in advance if this is a noob question.
I recently purchased a Pluto SDR and am trying to test it on a local FM radio station (104.7MHz).
I’ve changed the config of the SDR so it now operates from 70MHz to 6GHz, so it’s in range (set it...