It's all about the Software

how about feature that at the click of a button a text or xml file so that the whole configuration is easily attached to a post.

I'm new to using SDR radio / software. I recently purchased a HF+ Discovery, and running it with SDR Console (SDRC) v3.3 I recently downloaded.  It's working great, but how do I know if I'm leveraging the proprietary noise reduction algorithm...

Hi,
when adding the IC-R8600 to SDR-console (v 3.4) I noticed that both converter selection and invert spectrum where enabled.

I disabled both before saving, but does the spectrum has to be inverted when using the R8600 or is this something which...

I think there is a problem with applying a frequency calibration correction with the SDR receiver (a Zyncsdr / Libresdr) listening to the 70cm band (433.5 to 434 MHz) while the signal comes from a QO100 downconverter running between 10489.500 MHz...

Hello,
I haven't used my Pluto D for two months, when I start the SDR console (3.4) I usually, but not always, get the display below. What can be the cause?
Conn.jpg
73 Detlev

Hello folks,

Apologies in advance if this is a simple fix but I've failed to add an external radio to Console.

I have followed the instructions;

View-More Options-Enable External radio- Then restart.

Its the restart is where I have the...

I can’t get VarAC to transmit and receive using SDR Console, Virtual Audio Cables or Omnirig connecting to the Hermes lite. Vara HF, I’m not sure what it is doing? Anybody ever get VarAC to work with SDR Console into Hermes? Struggling. Thanks.

I have not been able to get the LimeRFE to work above 100 MHz with SDRConsole. What I have found is the logic levels on U9 (SW6_V2 & SW6_V3) are not correct at 222 MHz. As such it can not receive or transmit on J3 at 222 MHz. SW6_V2 has to be a 1...

SDRC v3.3

When rapidly changing frequencies, sometimes the external radio frequency does not get updated to match the SDR frequency. It usually tracks even when scrolling rapidly, but 5-10% of the time does not. The fix is simply to change...

Is there more information about MAP65 Support in newer SDRConsole beside of whats in the SDRConsole itself

To be able to use SDRConsole with MAP65 for X-Pol (H/V) antennas it need support of two coherent 96KHz I/Q streams coming from a Dual...

I just changed from ICOM 7300 to ICOM7610. On the 7300, I use a IF tapping card to get the signal to a RSP1B SDR, itself piloted by SDR Console and it works so well. On the 7610, I was hoping to use the IQ signal from ICOM that work with HDSDR but...

How can I use the Pluto Plus ethernet port with SDR console?

Hi,

to my knowledge the actual Aaronia support is limited to the v6 full version , not the ECO. So I wonder if it is planned to support also the ECO, as this is for sure the radio that will be bought by many hobbyists.

I own the ECO in RX/TX...

hello, i have a problem with sdr, namely when i connected a 3.5-52mhz longwire antenna, there appeared such dashed lines on the waterfall in sdr console v3.3, as if reflections of the broadcast station, rf gain is 29.7db
I have rtl sdr v4 Is there...

Being new to SDR is fun but has it downsides. I am using a Hermes lite 2 with SDR Console and have been able to receive well on 10, 15,17,20, and 40 meters. I am trying to transmit through a usb connected mic with no progress. I have tried to tune...

I would like to use sdr-console to tune into narrowband signals acquired by a Casper SNAP board.

So I'm looking for documentation on a suitable IQ data stream that sdr-console recognizes. The SNAP is set up to easily stream UDP, so I'm looking for...

This morning, Simon's World Map presented me with the attached error message Error.png

All other maps listed on the Select drop down box appear to load just fine when selected. It's just the LargeWorldMapNE3 that will post off this error. My first...

Dear Friends

I set my Lime SDR as shown in the photo to have an IF at 150 MHz.
In transmission it works perfectly from 14 MHz it transmits at 164 Mhz,
while in reception at 164 MHz I receive nothing.

Where am I going wrong?

Thanks 73 Arnaldo...

With regard to the Frequency Database feature, it would be nice, due to my aforementioned laziness, that it might somehow highlight broadcasts that should be on now based on the current time so as to not have to sift through a sometimes long list....

SDR console is my favorite program for controlling SDRs, the latest addition is a ZynqSDR/LibreSDR which comes in a CNC housing. This SDR it is equivalent to the PlutoSDR, in fact the Pluto+ with 2TX and 2RX but it requires modified firmware. What...

Subject: Assistance with Ingesting Raw IQ Data from SDR Console across LAN into Python on another PC

Hi, I’m attempting to ingest raw IQ data output from either the Data Repeater or the SDR Server in SDR Console using Python. I can successfully...

Hi all,
I have a RTL-SDR V4 and trying to use it with SDR Console V3 on a Win 11 laptop.
I've spent time familiarizing myself with the software and now trying to listen to incoming signals.

The problem is that the sound is terrible. It sounds like...

Hi Guys,

I'm a long time radio builder, and I'm planning a hybrid analog/digital RTX.

I am testing RF output with a spettrum analyzer using SDR Consolle with LIME MINI USB on the HF band TX (setting 3 MHZ Hf-TX)

In some bands, even if they are...

The spectrum of a spyserver shows op with a peak carrier on any entered receive frequency and a valley around it.
On certain higher frequencies the whole display starts bouncing up and down.

When using the SDR# client all is fine.

You can try with...

Hi,
I just installed P2 on my ANAN 200D and tried it with SDRC without luck.
Everything looks OK except the audio which is terribly distorted. Also.
signals look more like AM ? (Thetis works fine...)

What have I missed??

73 de LA6gh
Nils