Search found 785 matches
- Fri Mar 08, 2024 11:50 pm
- Forum: General
- Topic: CW on AO-100 (Help please)
- Replies: 11
- Views: 2198
Re: CW on AO-100 (Help please)
Bob, there will be different solutions depending on your hardware. What is your (or proposed) SDR? 73 Max Just re-discovered this thread worth a read through regarding Pluto and Lime for example where you would key, as you said, via SSB audio input. If you have Hermes Lite 2 (like me) then this has...
- Fri Mar 08, 2024 11:22 pm
- Forum: General
- Topic: CW on AO-100 (Help please)
- Replies: 11
- Views: 2198
Re: CW on AO-100 (Help please)
So gentlemen, I can not find an answer in FAQ's on this issue, so I would like to ask the many users with far more knowledgeable and experience with SDR Console a seemingly simple question. With both a CW Transmit mode and the ability to generate variable tones, can SDR Console easily be hardwired ...
- Fri Mar 08, 2024 4:15 pm
- Forum: Requests
- Topic: CW Mode "CW Tune function"
- Replies: 4
- Views: 1108
Re: CW Mode "CW Tune function"
When CW mode active, a means to park the peak of the CW signal in the middle of the filter window, like many HF transceiver's can do. I think it's essentially a search for peak signal strength +/- from the current VFO. Also the ability to choose CW mode side-tone. Therefore when using the CW Tune e...
- Wed Mar 06, 2024 10:01 pm
- Forum: Requests
- Topic: Compact Configurable RX tile to float and gestures for switching UI presentations of that control
- Replies: 4
- Views: 1108
Re: Compact Configurable RX tile to float and gestures for switching UI presentations of that control
I know it's not the same as what you are requesting, but have you considered a midi controller? Many commands are configurable to such a controller with tuning wheel and buttons. Also, a couple of shortcuts........ did you know that you can tune frequency using the keyboard left-right (x1 step)/up-d...
- Mon Mar 04, 2024 9:23 pm
- Forum: Forums
- Topic: Identity for hf and qo100
- Replies: 7
- Views: 1423
Re: Identity for hf and qo100
equipment is sdr play duo ic 9700 and ic 7300 these settings all stay the same no matter which identity I chose. 1 Radio selection omnirig maybe more but these are the ones I notice at the moment Max. Regards Brent Forgot the Omnirig settings! I'm not sure Simon can get those to save with the ident...
- Mon Mar 04, 2024 9:20 pm
- Forum: Forums
- Topic: Identity for hf and qo100
- Replies: 7
- Views: 1423
Re: Identity for hf and qo100
equipment is sdr play duo ic 9700 and ic 7300 these settings all stay the same no matter which identity I chose. 1 Radio selection omnirig 2 offset frequency 3 rf gain 4 if gain 6 agc 7 visual gain 8 tuner a/b maybe more but these are the ones I notice at the moment Max. Regards Brent By "Offs...
- Mon Mar 04, 2024 2:15 pm
- Forum: Forums
- Topic: Identity for hf and qo100
- Replies: 7
- Views: 1423
Re: Identity for hf and qo100
HI max thanks for the reply, yes i need two identities one for hf and one for qo 100. so i have one id called 7300 and one called qo 100. but when i get each one set up and then swap to the other one the settings don't change eg rf gain, offset frequency tuner A or B etc etc. I must be missing some...
- Mon Mar 04, 2024 10:14 am
- Forum: SDRplay
- Topic: Baud rate limit of 9600 for CAT sync with TS-570DG
- Replies: 2
- Views: 1274
Re: Baud rate limit of 9600 for CAT sync with TS-570DG
Hi Sam. Afraid it's me again (Max). I assume you already tried raising the baud rate one step at a time on both the radio settings and Omnirig? I don't believe it's likely to be an issue with Omnirig. I have used it with other software that needs it at higher rates (not an external rig admittedly). ...
- Sun Mar 03, 2024 10:13 pm
- Forum: Forums
- Topic: Identity for hf and qo100
- Replies: 7
- Views: 1423
Re: Identity for hf and qo100
Forgot to say, to get to Identities panel in the first place:
73
Max
73
Max
- Sun Mar 03, 2024 10:09 pm
- Forum: Forums
- Topic: Identity for hf and qo100
- Replies: 7
- Views: 1423
Re: Identity for hf and qo100
Hi all, is it possible to have 2 identities on start up. One for hf and one for qo100? I tried this but when I switched to HF console still shows qo100 settings and visa versa. I'm probably missing something obvious. Regards Brent G5TV Not totally sure what you mean by identities on start-up? I thi...