It's all about the Software

The signal I am testing/visualizing is an uplink cellular phone rf signal, but regardless of the signal type, there is a significant RF signal strength difference between what I can see in the Console vs a Realtime Spectrum Analyzer (multiple RTSA...

I just completed a UI prototype using the CAT protocol.
This hardware user interface consists of a Wemos D1 mini lite ESP8266 board and an HN3806-AB-600N rotary encoder. Although not using WiFi, I used an ESP8266 D1 mini lite because it was...

This is more of a how is the sausage being made question. When I have created a CSV file in Data Analyser, it has taken its information from a +/- 0.5Hz slice of spectrum.

For each timestamp, is that data the total power level within the +/-0.5Hz...

The latest extio available from Oscar Steila allows upto 140Msps sampling rate and 70MHz bandwidth, is it possible to add something similar to Console? Having 16bit performance up to 70MHz from the HF port will allow simultaneous coverage of 10, 8...

Hello,

Just getting set up with a new CloudSDR (as Simon is aware from my ramblings in another group). I am a big VHF and above searcher and DX'er and using CTCSS and DCS tones to identify unknown stations is a big part of that.

I notice under...

Server Version V3.0.27, LimeSDR not exist in the server radio definition.
Server.png

However It existed in the previous version V3.0.22
Server3.0.22.png

Can I fix this myself?
Or is a deeper containment required?

Updated 18.04
The console...

Ignore

Hi,

I looked at the Digital modes screen, and what I have, apparently,
is RTTY and the PSK ones, only.

Should there also be Sitor-B/Navtex ?

If not, any chance of including in the next rev(s), (with Acars too, perhaps) ?

Much thanks,
Bob...

When using the Receiver Noise Reduction NR3 my Transmit Audio is distorted. When I change to NR1 all is OK. I didn't think there should be a correlation between the receiver settings and the Transmitter functions.
73, Don

I like many others I guess, use Virtual Audio Cable (VAC) by Eugene (Evgenii) Muzychenko for piping audio to and from SDR Console and other pieces of software.
Well just recently it has stopped piping the audio. This may have happened when the PC...

Hi all,

I'm using .27 of the console. I would like to use the HF1 and HF2 inputs of the S3 for different antennas. How do I teach the scheduler? For example, he should switch the Asia antenna in the evening and the American antenna in the morning....

Hello,
I know, that V2 is not supported anymore, but I am still very often using the old Data File Analyser, because there is a possibility to import or export TAGs. Few days ago, after a few weeks pause, I have noticed a problem with a TAG label...

Hi all,

I have a problem with frequency synchronization with SunSDR2PRO. Both SDR Console and EESDR are set to OmniRig. After switching on, the frequency is synchronized, but only once. The same configuration with the FLEX6500 works perfectly. Has...

Hi,
When playing back a recorded I/Q file, I don't get on SDR console the same bandwith than that displayed by the Analyser :
On the right hand side window (analyser), the recorded range starts at 16.64-0.9216=15.72MHz and ends at...

I have posted this to the Skywaves forum - thought I would include it here.

It's a short tutorial on how to loop a small part of a recording in SDR Console.

I'm not sure if this has been reported already and if it is a bug or such kind of oddity.
So far I've seen it on the R2, the RSPDX which I use remotely doesn't show this behavior.
The frequency of the radio (the real frequency, not what is shown by...

Minor UI bugfix.

Click this link

Sorry to be a distraction, Simon...
Are you willing to share the design differences between your/Moe's new SAM implementation and the old AM version?
Before this, I assumed binaural was already carrier-synchronous.
Many thanks
Paul

Normally the frequency change either via the numerical or the spectrum display is instantaneous and without any delays, but now for the second time in a couple of months this is not the case.
Jumped over to my Linux drive and tested the radio's with...

Hi,

Very minor UI bug fix and also performance improvement.

Here's the link.

I was running v3.0.26 before, installed the March 26 v3.0.27 and the RDS clock time or CT is showing an hour ahead on all stations that send it.

My region uses RDBS, 75us, and these are strong local signals with the thumbs up icon, bit correction...

Severe wind storm here in New England, power out 1530z. Currently on 20KW diesel generator with all servers powered up.

I even took some screen shots while the neighborhood was powered down to compare when it returns! No more electric fence noise...

Hi,
due to the lack of a self-sustaining ‚Split-Function‘ some people use the RIT for that purpose e.g. in pile-ups. The consequence is, that all other added RXs take over the enabled RIT-function and the offset. This behavior is not only...

Now we're in Summer time I'm seeing a discrepancy (when replaying recorded files) in the time stamp on the waterfall, which is showing correctly as UTC, and the time shown in the the bottom left box of the waterfall and in playback navigator. Both...

Hi,

Oops:

I wrote about this previously, but posted it in the general forum, rather than here in
the Requests forum. Sorry.

Re the WinRadio G-31 Excalibur:

I understand that the unit has a hardware pre-amp built in.

The very old WinRadio...