It's all about the Software

I have tried to capture diagnostics so apologies for long post

Having problem with ELAD FMduo and SDR server.
It was working up til 2 weeks ago.

My setup have a win 11 laptop running v3117 (sdrserver) with an airspy hf+ discovery and elad fm-duo...

Small issue I have with my fmduo tx/rx is that sdr console identifies it as rx only model
As such I have no way to switch antennas.

Also I cant see a way to disable LPF and thus go past 54 MHz

Any ideas team?

SDR-Console, wjst, VAC.
Everything ran fine on win-7, ran fine on win-10....Win-11 I have nightmares. I have a high school science project going on here with my audio settings. What works one day, does not work the next. Any setup help would be...

(1) I will supply screenshots if needed, just tell me what to provide.

I used win7 for the longest time. Everything worked fine. I had to replace my pc and it came with win11 installed. I am new to win11.
Here is my issue: Radio on, SDR console...

I have been running win7 forever... I think it's about time to migrate to win10. Are ther any issues I need to be aware of?

Good morning, guys but it is possible with the duo to activate a mechanical ptt (button) von the softwsre I'm not happy, thanks.

I got the chance to buy an Elad-duo. After reading the sdr-radio website, it is still not clear what I could use to activate the PTT with a down to earth simple setup. Any suggestions?

73' Ron
ON2RON

My first setup of SDR-Radio with FDM DUO. Most likely I am overlooking something in my configuration.
TX works, but RX not (no audio signal nos waterfall).
FDM-DUO works fine in RX and TX with FDM-SW2 on the same PC.
SDR-Radio 3.1 works fine with...

Can anyone test if there is more than about 1.5 W Output possible?

Having returned to using the Elad FDM-DUO more out of curiosity than need, I find that the menu option to reduce Visual Gain on SDR-Console is missing.
The Visual Gain features I used to allow me to control the S-meter reading, which on 50MHz sits...

What are you doing for CW? Apps?

First, I'm loving the integration between the ELAD FDM-DUO / DUO-ART 120 and SDR Console. I've completely configured console to use my combo of Log4OM, WSJTX, and associated utilities, all is working fine.

My problem occurs when starting SDR...

cwtype:
It apears to add extra characters then ends abruptly. I just sent (to a dummy load at very low power) a series of V's 3 V's were ok, 4 v's ok, 5 v's came out VVV-didididahdit. cq cq cq de n2eik came out as cq cq several dits and dahs...

New to SDR-Console.
Using FDM-Duo.
The RX is fine but I can not transmit. I use a foot pedal and I CAN key the ptt but I can not get my usb mic audio connected, also I can not choose any transmit options, the transmit pane is greyed out.
Any help?

This is getting kind of frustrating. Just when everything (phone, cw or wsjt) seems to work fine.... the next time I open console and wsjt I cant get wsjt to send full audio to console, just a few miliwatts come out. I start checking my audio...

Any help on that?
Console and rig on com3. WSJT wil not share the port. (as expected) and I am not quite sure what the diff is between console and SW2, as wsjt works flawlessly with SW2.

Had a report that ESSB is not working, specifically audio bandwidth is restricted to 4 kHz.

This may be a DUO setting, will check. Other radios such as Pluto are working OK with bandwidths > 4 kHz.