It's all about the Software

Hi,
For various reasons my antennae are some distance from my shack so upto now I have used ICRON USB ranger 2204 which allows two boxes of electronics to be connected by network cable, the box at the antenna end has the SDRs pugged into it and the...

Hi all , is there a ExtIO for the RSPdx and spectravue? , i have spent several hours looking about and no luck so far , no real reason or urgency btw as sdrc and uno are just fine but i would just like to try spectravue just because :roll:
cheers...

After reading the forum existing comments about non-starting, I made sure I have the latest API from SDRUno, and the latest DLL sdrsourcesdrplayv3.dll

The RSP2 is correctly identified by the software. However, start does not start the app. Help...

Hello all. I'm hoping someone can point out what I'm missing/doing wrong. I have SDRuno V1.42 1710 installed, and it shows 3.15 API. Console is the latest Build, see pics below. SDR Console works with the radio, but it shows as unknown , and...

Hi,
I updated SDR Uno to V1.42 1710 on my PC and ran it up with my fully functioning RSP2 that had been running happily under SDR Console 3.1. No problem.
Then updated SDR Console to v3.3. Now the same RSP2 will not start.
SDR Console 3.3 works...

Hi,
I have had SDR Console (V3.2 build 2731) running happily with RSPdx for several months. A couple of weeks ago I unplugged the PC to move it. Now reconnected I find I have a problem. SDR Console runs happily and appears to be responding...

I have down loaded Consol V3.3 and installed on Win 10 64 bit.
I have also installed the API (3.15 from SDRPLAY) and can see during the installation that the driver was shown for the RSP1B. I purchased the RSP1B a couple of days ago, new.
In Console...

Hey everyone,
First time poster. Enjoying the many features of SDRConsole!

I'm questioning why use of SDRConsole required me to lower my baud rate to 9600 when connecting the program to a TS-570DG via Omni-Rig.

Other programs I have have no issue...

Hi there folks,

Thanks for letting me in the group :)

I recently purchased an RSP duo and have been really enjoying using it with SDR Console. I think Console is pretty amazing!

Unfortunately, I haven't been able to find anywhere how to select...

Hello,

my Name is Heinz from Germany and please excuse me if I made mistakes.

Since yesterday the SDR Console works really fine, even in HF and I am a little bit proud ;-))

But since today my left display side is completely filled and functions...

Hi, Can anyone advise when support for the RSP1B will be available in SDR Console. I note from SDR-Radio.groups.io website that Simon has tested it and has it working, however it's unclear to me if I need to wait for a new release or are there some...

I am running SDR-Console Bete v3.3 build 3131 with the SDRPlay RSP1a. I have noticed that the waterfall contrast always changes. I don't know what causes this. The best way for me to illustrate this is by video.

Is there a way to stop contrast...

I came across this splitter the other day (i'm not associated with them) , i need one for the FT-2000 and the Rspdx using the rear in/out and rx button on the 2000 .

One is turning up in a few days , it looks nicely made with input protections ,...

I don't see an option to get the SSB medium under receiver. What do I need to do to get this?

Thanks

The Fusion 13 option doesn't work so well and this is on a 2021 Mac so it's fairly fast. Lots of pops etc and slow. Never did get the receiver panel to show SSB. Audio very poor on FM. The box to set configuration wasn't consistent. Maybe Parallels...

RSPdx , after it was sitting around for a month or so unused , i plugged it in and fired up sdrc and the noise floor indicator needle was at a 8 and the s-meter needle was stuck at a S-9 and nothing i did (adjusting rf-gain/if gain) would get them...

Hi all , is there any issues known about leaving the SDR plugged in to USB at all :?:

I have been lately leaving it plugged in on shutdown on win10 (after closing the software) , its on a port that does not have continuous power enabled and then...

Hi all , whilst nothing can be protected by a direct lightning strike (Millions of Volts and Thousands of Amps) and i always nearly keep a eye out for any storms in this area that might be coming way before one can hear any thunder btw , so i...

I noticed in v3.3 that under SDRplay there is only V2 and V3. What should be selected for RSP1A receivers? The reason I ask a person using the latest Windows 11 update is having trouble getting SDRconsole v3.3 to find his RSP1A. With the latest...

Hello,
My name is Peter and I have been a radio amateur with the call sign DO1PH for 2 months.

I have a problem with the SDR console working with the SDRplay RSPDuo.

I monitor with the RSPDuo 2 pan adapter (1st IF 38.85MHz for 2m, 2nd IF 46.35MHz...

After updating SDRUno for the heck of it, I noticed that the SDR Console waterfall would freeze but the radio still played. Stopping and starting SDR Console would not fix the frozen waterfall. You would have to close and reopen the SDR Console...

Hello there,

Can anyone help please . My Rspdx and sdrplay are failing to start also my rtlsdr v3 takes ages to start as well now. Using 3.1 2320 buld. Have uninstalled and reinstalled still the same. sdruno works fine with rspdx and sdrplay....

Hi,

I am using 3.1 build 2418 and having just recently purchased an RSP1a, it appears not to want to start. To get it to do, so I have to restart my WIN10 PC and then it will do so. When I first turn on the PC or if it has been on for a while,...

Thanks for the software Simon, which I have used daily for many years. I have loaded the SDRPlay 3.08 service in conjunction with SDRUno 1.41 beta and the latest SDRC version 3.1 build 2340, which I believe should run with API 3.08. When I try to...

When using the RSPsx in HDR mode if i try to center the frequency in goes back to normal mode.
Have to but it back in HDR mode every time after using the center button on the drop down beside zoom.
Only ME?