It's all about the Software

Hi
I hope you forgive my ignorance.
To use SDR console on a Windows PC to control a raspberry pi 4 with 1 RTL-sdr dongle, what do I need to install in the raspberry (drivers, software, etc.) ?
Many thanks in advance
Regards

So gentlemen,
I can not find an answer in FAQ's on this issue, so I would like to ask the many users with far more knowledgeable and experience with SDR Console a seemingly simple question.
With both a CW Transmit mode and the ability to generate...

Hi,
I have Sdr-console on my pc.
I would like to copy all settings/data (memories etc) to my laptop.
Purpose is to take my laptop, radio, antennas when I am camping to 'listen around'.
Is that possible?
How can I do that?
Thanks in advance.
Paul

Hello dear Forum-team, hello Simon!

Please let me take this opportunity to say thank you for this really great program!
I think it's proof, like Ham Radio Deluxe 5, that amateur radio can set new standards in communication.
Many thanks to Simon...

Hello,
A continuing problem, I am having with the SW is that my audio levels are very low. I am listening to WWV right now as selected from the favorites menu. My volume level is set to 50% and i have head phones on the signal is above S9+20 and yet...

Hi Simon,

Do you think it would be possible to add a stereo AM decoder in future releases? I have used the binaural option a few times but it's not quite the same as the real C-QUAM stereo and it would be really great to DX some of the stations...

Looking for comments on an idea for a variant of @Simon’s excellent Signal History.

The context is Medium Wave AM BC DX – weak signals – when a carrier can be prominent, but ID relies on detecting the elusive audio.

24-hour Signal History graphs...

Title says all. Drivers installed fine. SDRuno sees it but crashes on Play Win 7 Pro 64

thx

bob

Hi Guys

I have installed V3 but I ca't get my layout to look anything like the videos that I Have watched. Not sure if I messed up on the initial install or?

thx

bob

Hello,
Here is the context: I am using a FT-991A on QO-100 with DX Patrol converters (144.500 MHz IF). Most of the time, I do SSB or FT8 modes.
A Panadapter from SDR Kits is installed ( which outputs a 70ish MHz IF to an Airspy HF+ Discovery.

The...

Hi folks. I am still a newbie to SDR console but am posting because I searched through many pages of questions raised, but none seemed to be quite this issue.

Setup:
SDR console 3.3 running on 64 bit Windows 10 laptop
Pluto Plus SDR into Analog...

Hello everyone!...but what combination of waterfall palettes do you think is the one in this video? I've tried the various ones available but none of them look like us... I've also tried Jon Herman's ones but nothing.....

...among other things,...

Is there a way to launch multiple instances of SDR Console automatically at Windows startup? I currently run 3 computers running 2 SDR's each and 2 Instances of SDR Console on each. Right now if the system reboots on it's own for some reason only...

Team SDR-Radio (SRD Console)

I am able to run a stand alone version of console v.3.3 with no issues using the RSP Play Duo SDR receiver with a Omen AMD Ryzen laptop. The radio rig is a Yeasu FTDX 101d and I am driving the SDRPlay DUO via the IF...

Hi,
I use 2 screen on my PC and when I use SDR Console V. 3.3 the screens go blank either both or one and after a few seconds they come back on again.
When I am not using SDR console this does not happen. Has anybody had this issue too? The typed...

Hello,

I imagine the screen to do it is somewhere, but can't seem to find it.

Is it possible to create a Notch filter to notch out, e.g., a (selected) small am spread of frequencies with the program ?
Where, and/or how, please ?

(I know of the...

Hi,
I am wondering how SDR Console (v 3.3 ) handles the downconverter settings for by example LNB use, when the LO frequency is higher as the RX frequency.

I have connected (by bias-t) an LNB for the 19.7 to 20.2 GHz range, which has it's LO at...

Hello,
New SDR-Radio user, how to switch from straight key to paddle? and how to change the CW speed in the SDR-Console 3.2v?

Thank you

Al
W4RAM

good morning...a question that will surely spark the laughter of many but I'll ask it anyway...😅..with the same receiver and antenna (e.g. rsp1a and mla30 for example) varying the software (sdruno vs sdr console always for example) do we have the...

I'm trying to calculate the dBm of some raw IQ samples I got via gnuradio but I can't seem to find a correct link. I looked at the ADC my hackrf one uses but the IQ values don't seem to be directly related to the voltage measured. This is the...

I have used an RTL-SDR and Console as a panadapter by piping my FTDX-1200 microtune output into the RTL-SDR. It's worked very well.
Recently when I run the program it doesn't display anything, seems to have problems finding the RTL-SDR radio, and...

New user, so be gentle...
So far, things are going well; I have an HL2 TRX and I have set up several keyboard shortcuts to perform various functions - toggle VOX, toggle TUN, toggle XMIT, and bring up the RX and TX DSP Windows.

When I bring up the...

Hi all and thanks for the add. I have a quick query.

I've recently come to the software and am trying it out with my RSPDX and so far so good. So my query is is there an easy way of importing the Mem Panels from SDR Uno to Console's memories or do...

I like to use SAM in a number of cases and would like to know when the frequency is locked and what the offset is if locked or not. Thanks and enjoy, John.

I made some recordings around 2402 MHz with a bandwidth of 5MHz, when I use = audioread( ) in matlab, I only get a samplerate of 5MHz, while it should be atleast 10.
Is there any way I can manually set the samplerate or should I just record a bigger...