It's all about the Software

I'm using 4 VRXs, so I really don't need the signal meter & it's getting in the way of the spectrum peaks. Any way to either move it to another portion of the window or just get rid of it altogether?

Thanks

Bob NO6B

Anybody have any idea why I can only get 300khz bandwidth while connecting to an RT820 via SDR Server V3?

Wondering if such a display is feasible, given a decent antenna array and multi-channel receiver...
Obviously need to tune a specific channel (e.g. a VHF BC frequency).

Please excuse horrible graphic

This very occasionally seems to freeze Console, no crash dump.
RSP1A (but FDM-S2 possibly OK?)
Just upgraded 3.0.15 to 3.0.24.
Seem to recall this from last year too.

Nothing to get excited about, especially with my Win7 and frequent low...

Not sure where this should go - but so long as people will read it and tell me what is going wrong.

I am trying to bypass the manual entry into the Scheduler because what I want to set up would take forever . In am trying to import a csv file...

Just an observation.

My PC faced a battle today when running Console at the same time as watching F1 qualifying on Sky Go.

Turned out to be a bit of a battle. Sky Go won!

Console graphics just stopped updating. Guessing Sky Go uses CUDA and takes...

I have been using SDR Console for some time now. The most recent version I used was v3.0.3 build 1263. I use a RTL-SDR v3 with bias tee active to power an LNA at my antenna. Today the laptop that is running this program rebooted for a Windows 8...

Air Spy Win 7 Windows photo viewer Shows blank console and external radio data only ?? DanHam
Screenshot-2020-09-08-082954.png Screenshot-2020-09-08-082954.png

Hi guys.

I would like to set up sdr-console to feed 4 channels /each to different VAC output/. I am using RSP1A - and that covers up to 10MHz spectrum. The problem is that it's working if I use RTL-SDR with 2MHz visible spectrum, but when I try to...

I run a Dell latitude (i5 8gb) as a server (June 2020 build) to my i7 16gb desktop (July 2020 build) (avoids antenna feeder going across the flat). NESDR Smart and Hamitup. For months this has been fine, but in the last two weeks it crashes within...

Hi all,
SDR Console v3.0.24 is only partly responding to my Kenwood TS850s. It connects to the External Radio function just fine and changes the frequency that the radio is on but nothing else eg no S meter reading etc The software works...

I wish to do some side by side comparisons of 2 sdr radios..

Is it possible to run 2 radios at same time with 1 pc?

Perhaps with 2 sdrc running?

I have no idea..( but do not wish to try before asking.)

Thank you ..

Does this all the time..

If i change rx mode quickly ( was hunting interference.) then the big centre spectrum and waterfall freezes..
Tx frequency freezes..
Rx if still works..
Then after a minute or so the software crashes/ freezes big time.

Can...

[Copied here from groups.io, as it wasn't answered there. Link to groups.io thread ]

I have some favourites set up that don't have saved receivers (for signals that are too wide for any of the SDR Console receiver options, just for seeing them on...

Hi Simon,
i am using SDR Console 3.0.24 64Bit on Win10 and HermesLite2 or with RSP1A
The Noise reduction NR3 seems not to work like in 3.0.23.
When i am activating NR3 in 3.0.24 the major noise floor seems not to be reduced. It sounds like the...

Hi,
is it possible to set TX Bandwidth, both audio and RF to 22kHz? I made a custom filter, but it seems only 4k is coming through.

Thanks,
O.

(reposted from IOGroups):

Does SDRC have a way to log average received channel power to file at
regular intervals? I was doing this with SDRuno & it works very well but as
I'm planning to move away from SDRPlay products I'll eventually need to use...

hi Simon,

I'm using a HL2 with a 144/28 transverter to work weaks signals on 2 meters.
Therefore I have a VAC from RS to MSHV

Works fine but I also want to listen to the signal and 'assumed' the RX button in the monitor would let me listen to it...