It's all about the Software

I made some recordings around 2402 MHz with a bandwidth of 5MHz, when I use = audioread( ) in matlab, I only get a samplerate of 5MHz, while it should be atleast 10.
Is there any way I can manually set the samplerate or should I just record a bigger...

Is anyone using the SDR console as a poor man's spectrum analyzer along with an SDR RX and a noise source?
What are the best SW settings for this purpose?

73 de IZAFL

Hello Simon,

On my system the CPU and GPU performance graphs are not indicative of the System Performance tool.

See attached screenshot.

73 Hauke (VK5HW)

Hello,
I have a problem with the mouse in SDR Console, latest version, not beta version. I use Winsows 11 as the operating system.
The problem presents itself as follows:
I can move the mouse in the spectrum, but I can't set any filters, and I can't...

First post here, new user of SDR C so I hope that someone has an idea of how to resolve a tuning problem.

Elad FDM Duo as the main receiver (not Remote rcvr) on Com3. Works great with SDR Console but I have a query when using Dx Commander. I can...

Hi,
I'm using SDRConsole for the first time. Setup is W10 PC with SDRPlay RSPdx. All working fine with single band display.
When I select Multiband and, for example, Amateur CW, I get the full matrix on screen of the expected bands, but only one...

Hello
I'm having problems with my new windows 10 computer.
the sdr console frequency is fixed and cannot be changed, I can punch in new frequency but the spectrum stay's the same .
I can zoom in and tune in to stations on the frequency span that the...

I would like to read the set frequency on console via arduino.
In options, cat (serial port), I/O Test, I set the port and sent the frequency, arduino reads it correctly.
After I go to port selection I set the port as I/O Test, but nothing happens,...

Good afternoon,
I have a question about the program.
This program has API to link a guard book program like Swisslog.

The need is to be able to capture the keyer from Swisslog to be able to make the calls from the book on guard.
Could you be...

Hello, is it possible to receive DAB+ signal with SDR Console ?

Hello there!

I'd like to ask something that I did not find in the documentation, neither was I able to find something concrete in the forums about it.
-> What do the percentage sliders for RX filter and TX filter exactly do (Radio section on the...

I am using the latest version of Console with an Airspy HF Discovery, bandwidth set at 912kHz. I would like to make IQ recordings of the entire MW band from 530kHz to 1710kHz. I tried using the MW settings in Favourites but the resulting recordings...

Hi all,

Is it possible to override the built-in 200 Hz high pass filter when using narrow FM? Although the majority of voice intelligibility is probably above this, I would very much prefer to adjust this and bring some of the lower frequencies...

Hello,
I want to record more than one audio stream within 500khz of bandwidth with only one SDR. I am trying to record NFM Local EMS and NFM Local LEO. Is this possible.
If I use data recording it has too much dead space and takes up to much...

Hello,
I have SDR console V3,2 installed and running fine with Airspy SDR+Discovery. Also working fine with web based SDR's. However I have not been able to get audio from Headphone jack into external powered speakers- always coming from Dell...

Hi
I probably forgot a parameter in my SDR Console setup using a RSP1A and a Yaesu FTdx via Omnirig.
At the start of SDR Console the «External Radio» window starts automatically and shows the frequency of the TX from Omnirig as expected but the main...

I have 2 receivers windows open both on different frequencies, is it possible to monitor the audio from both at the same time without having to mouse over each window

I am trying to make up a database of some local frequencies but I cannot get the list added to the software, the Add to Database button is always disabled.

Does anyone have a sample csv with populated data I can look at please

Anyone try using a QDX with SDRConsole? Recent firmware has allowed a I/Q output, so the full 48khz bandwidth can be used. Someone on their forums mentioned he was able to get it working using one of the existing radio entries, OmniRig and the...

Anyone else?

Only on the 2Mhz bandwidth setting and not on any of the other bandwidths , win10 64 , symptoms are all is going well then all of a sudden whether just listening (no interaction with the gui) or actually interacting like zooming or...

Hello,

Any way to use an Icom RC-28 rotary encoder with program ?

If not, what's the physically smallest similar item that will work ?
Very limited desk space.

Thanks,
Bob

Hello,

Blame my ignorance on old age now.

How do I select the Virtual Audio Cable (VAC) as the audio output ?

How do I configure it ? Trying to feed the Navtex decoder YAND via a new Icom R8600 and Console.

I understand the program has this as...

I use the auto-mute function to mute SDR Console when I'm transmitting. When the audio recovers, is mutes again, then recovers. The double process takes long enough that I miss the first part of the QSO or Callsign of the caller. What am I doing...

Well that's what i think it looks like travelling across the screen , they can go up (left to right) or down (right to left) and a laugh to look at , also associated with a chirp sound .

They be an Ionosonde
if anyone was wondering , one can see...

Is there any way to lock the zoom level? I zoom in/out to a preferred bandwidth and when I mouse-click a frequency, the zoom changes back to the middle of it's zoom range. I'm constantly zooming in/out, mostly out. I like to see a larger bandwidth....