It's all about the Software

Careful analysis of this common video of 3017 and 3025 shows :
1. signal level difference between these two versions S meter and marker level is 2-3 and 10-18 respectively
2. spectrum analysis in 3017 is real time while in 3025 is smoothed . I...

Is it possible to set the IQ recorder and continue to use a receiver without the recorder modifying its centre frequency?

Last night I set the recording session centred on 440kHz with a BW of 500kHz and ticked the Lock Radio Frequency box and hit...

Hi!
If using the Satellite Automatic Schedule and selecting Enable Tracking in the satellite control, the antennas are always tracking the satellite even if the satellite is not visible.
If de-selecting Enable Tracking in the satellite control, the...

The 3.0.25 has been installed in a new folder retaining the older 3.0.17 in its folder. The installation was very simple and faster thean the nominal It seems that all parameters form the 3.17 were transferred by itself to the new version
Now the...

Hello again
Because many seen but none responded ion my 3025 findings I repeat the questions separately starting with video grabbing
1. This seems mostly as screen grabber instead of window grabber Therefore if another program momentarily is shown...

The 3.0.25 has been installed in a new folder retaining the older 3.0.17 in its folder. The installation was very simple and faster than before and in the end most parameters were transferred by itself to the new version

Now the mysterious : v3.025...

got it all working..wow...now got tactile rig plus excellent rx..

except for i can not mute the elad /sdrc in tx.

everything is checked to make it mute as per the instructions on sdrc webpage.even ticked the rx mute in sdrc transmit options...

Using 3.0.25 64bit on Windows 10 on Dell Vostro 470 with RSP1A and getting random crashes. Task manager reports SDR Console not responding and memory use slowly increasing. RSP1A is plugged directly into front panel USB3. Unable to reproduce at...

Trying out the latest V3 with n IC-R8600 here.
Install went smooth. Upon launching the program I was able to get my radio to work.
But the screens are stacked and having lots of grief trying to get things arranged. I was the manual to try and sort...

I am struggling to get used to just using pc and sdr for my amateur radio needs.
I still much rather use the yaesu ftdx1200.. at my location with my antennas it performs as good as the hl2 and elad duo..better tx than both the sdr’s.
I like the...

As above but tx or rx dsp windows ( which are docked) also scrolls up and down at same time..

When it does this waterfall / spectrum freezes..

Does this with elad and hl2.

Sometimes its rx window, right now its tx window..

Sdrc v3.25

Thanks.

Hello

Wondering if I can reduce the tx latency on my elad duo.
It takes circa 1/2 second from talking to audio being transmitted by duo.( and a whole 1 sec to appear in my headphones if I monitor tx audio.)

Is this normal?? I understand there will...

Just installed 3.0.25, running it locally connected to an R2.
The audio is stuttering. Back to 3.0.24 everything is fine.
Screenshot attached.

73, Max N5NHJ

Hi,

After some hours of operation, the (virtual) memory usage grows up to 50GB and more (and keeps growing and growing). While RX and TX audio keep working without interruptions, the UI reaction gets noticeably slower. Physical memory usage stays...

Hello, I've just installed .25 over .24. I'm hearing a constant tone at approximately 200Hz while receiving weak signals in the AM mode. It sounds like the same tone that occurs in SAM mode when receiving various amateur radio signals that have...

I have looked all over the SDR-Radio website and I cannot find a download link. Thinking it might be at the end of the request for donations, I went there and made a donation which lead me nowhere. I am pretty sure my unattentive blindness has...

I'm using the latest version of SDR-Console V3, and whenever it is running the screen doesn't turn off after the 30 minute idle time set in Window's Power & sleep settings. If Console isn't running, the screen turns off as expected when the system...

Hi
maybe something i have done?

elad fdm duo..all ok on 3.24
updated to 3.25..

now have no tx power from duo..thats on tune and tx.all modes..DUO does go into tx, just no rf out.tx out levels are set to max.
rolled back to 3.24..still the same.....

When switching agc from slow to medium or fast. Crashes the displays.rx still working but all displays freeze.
Have to restart sdrc to fix.

Always does this..windows 10.

Regards..

Hi Simon,
just installed the .25 Version and have some issues which i can't remember having them with the .24.

Whenever i maximize the console window to monitor 1 or monitor 2 with the little monitor icons in the top right corner, some parts of the...

Hi,

Not at all sure if this is practical, , or even if it's a good idea.

But, and it's likely it is only me, but I spend a lot of effort in
coming up with a good compromise between the RF Gain and the IF Gain (when AGC is Off).

I keep thinking...

Is it possible to have the ‘mode’ - USB, LSB etc. on the quick access toolbar ? I can’t find the ‘buttons/s to add if it is !

Thanks !

Steve Jerome

Hello

A question...
I have an RSP SDRduo here.
I have now configured the console for the QO-100.

Now I want to work again with the SDRduo on shortwave with the appropriate parameters.

How can I do this without changing the settings for the...

I'm trying to calibrate my Nooelec R820T2 SDR & TV Dongle but each time I change the calibration setting +or - SDR Console stops receiving a signal in the waterfall. I have to press stop and then start again to receive a signal. Two screenshots...

When using SAM or ECSS modes, how can I see the actual frequency of the station's carrier? The frequency display in SDR Console now shows the frequency as set by me, but not the real carrier frequency. Thanks!