It's all about the Software

Does the checkbox in SDR console that enables the use of an external reference clock result in setting FPGA register 0x00CF(0) in v2.4 of the LimeSDR Mini? If not, what is the simplest way to have this register/bit set when using v2.4? Thanks for...

I am trying to run 3 WSJT-X instances on 3 different bands fed by 3 RX channels defined in SDRC. I can get the 3 audio stream to the WSJT-X instances but when I set the band in one of the instances, all 3 instances change to that band. I am using DX...

I am using and RSPDUO with the bandwidth set to 10MHZ. I have 3 receivers at the FT8 frequencies for 10M, 12M, and 15M. When I select the 15M receiver, the audio on the 10M receiver goes away. The greatest spread between the receivers with audio on...

Hello,

I am currently using the SDR Console v3.3 program, and I would like to view the frequency and level values within a specific frequency band. Specifically, I want to know if there is a feature that allows me to save the frequency and level...

There is a pop-up window (via Ctrl key) for frequency input, but I cannot find a way to set the filter width in a similar way, instead of dragging the green lines with a mouse. Am I missing something, or there is indeed no way to change it manually...

I have been in the Ukrainian Armed Forces since May 2022; I joined the ranks voluntarily, to defend my country against the Russian invasion. (I did the same in 2014, was seriously wounded in August 2014, etc.) I have been doing some radio monitoring...

Hello all!

I am using SDR Radio with Ergo4 and my Elad S3. I've noticed that every time I switch bands in favorites the volume defaults to 50%. This means when I schedule recordings that require a different band and higher audio, the audio on the...

Hello, is it possible to receive DAB+ signal with SDR Console ?

The intermod on the RTL-SDRs is well documented and I was experiencing some on Friday evening. I scanned through 6m and was surprised to see a bunch of sideband convos. So I listened in and realized I was hear the 40m late net check ins. I know that...

Hi,
I use 2 screen on my PC and when I use SDR Console V. 3.3 the screens go blank either both or one and after a few seconds they come back on again.
When I am not using SDR console this does not happen. Has anybody had this issue too? The typed...

Hi I have purchased a new Aaronia SPECTRAN V6 ECO 150XA-6. The latest SDR Console said can support SPECTRAN V6 (but not sure if is only V6 or both the V6 and V6 ECO) by SDK, I tried that on the V6 ECO, looks like it can see the hardware and detected...

Does anyone know of a plugin that works for automatic freq control. on a dish setup with c band LNB ADSC data. I get alot of drift with the sun peaking in and out of the clouds. it would be nice to have a AFC to follow the drift of the freq..

I think I'm missing proper settings in SDRC when transmitting and/or when using in conjunction with JS8Call.

Is there any particular setting I need to look for when TXing in HF or digital modes?

I use External Radio and the panadapter reacts...

I don't recall setting Console this way, but what is the setting that causes SDR Console to open when the computer boots up? Not sure if that setting is in Windows or SDRC.

I am trying to run SDR Console connected to Pluto on a remote machine. I am sending the audio from my local machine to the remote machine with Remote Desktop Connection. When I transmit, I get a lot of noise on the transmit audio in Console.

I am...

Hi,
I use the SDR-Console V3.3 with two different radios.
1. Adalm-Pluto as RX+TX for my QO100 setup.
2. SDRplay RSP1A for observing local FM-repeater on 438MHz.
While switching between these radios I use previously stored custom layouts. This do...

One of SDR Console's many fine attributes is the ability to read files recorded by Jaguar software (for the Perseus) at the 1600kHz sample rate.

Background: Jaguar can record at the Perseus' software's standard 2000kHz rate, but a separate 1600kHz...

Hi
I hope you forgive my ignorance.
To use SDR console on a Windows PC to control a raspberry pi 4 with 1 RTL-sdr dongle, what do I need to install in the raspberry (drivers, software, etc.) ?
Many thanks in advance
Regards

So gentlemen,
I can not find an answer in FAQ's on this issue, so I would like to ask the many users with far more knowledgeable and experience with SDR Console a seemingly simple question.
With both a CW Transmit mode and the ability to generate...

Hi,
I have Sdr-console on my pc.
I would like to copy all settings/data (memories etc) to my laptop.
Purpose is to take my laptop, radio, antennas when I am camping to 'listen around'.
Is that possible?
How can I do that?
Thanks in advance.
Paul

Hello dear Forum-team, hello Simon!

Please let me take this opportunity to say thank you for this really great program!
I think it's proof, like Ham Radio Deluxe 5, that amateur radio can set new standards in communication.
Many thanks to Simon...

Hello,
A continuing problem, I am having with the SW is that my audio levels are very low. I am listening to WWV right now as selected from the favorites menu. My volume level is set to 50% and i have head phones on the signal is above S9+20 and yet...

Hi Simon,

Do you think it would be possible to add a stereo AM decoder in future releases? I have used the binaural option a few times but it's not quite the same as the real C-QUAM stereo and it would be really great to DX some of the stations...

Looking for comments on an idea for a variant of @Simon’s excellent Signal History.

The context is Medium Wave AM BC DX – weak signals – when a carrier can be prominent, but ID relies on detecting the elusive audio.

24-hour Signal History graphs...

Title says all. Drivers installed fine. SDRuno sees it but crashes on Play Win 7 Pro 64

thx

bob