It's all about the Software

Hello Community,
Using a R820T Dongle, I started playing with the Console. I had found the step -button in the Mode -square qiet helpful to change the frequency steps for special demands.
Since this morning the step -button is missing and I must go...

I have an RSP1A which I've used with SDRuno. I'm needing to run the WF for as much as 12 hours, either a coarse increment (which is fine as I'm looking to see if the noise level changes) or the ability to scroll back in time ... can Console do this?...

Greetings All

through an unknown event my receivers (most of them) became 'minimized', offering only the options to edit or delete, but not to select/use

what did I do ?

can this feature be toggled off indefinitely ?

Thanks & Best 2021 !

I use SDRC as a panadapter with my FTdx5000 transceiver. Normally, I don't need to see anything other than the main spectrum and waterfall panes, which I think is referred to as the RX window. I keep the RX window set to its smallest available size...

In the V2 version of the waterfall, the lines were hidden by the VFO. They remained only in the spectrum. In the V3 version, the carrier wave remains and is hidden under them. Could it be modified as in V2?

Ok, while writing this post I remembered I should try a different USB port, obviously it fixed the problem after I had written this post. So I decided to upload it anyways as a reminder to try a different port.

Hi there,
I'm having the issue that...

Is there anything worth looking at that would help as a tutorial on I/Q files as generated by SDR Console (and SDR software in general)?

After looking at some sites, I'm clear on the idea that I/Q data consists of complex numbers representing a...

I have 3 SDRPlay radios on the same PC and want to have an instance of SDR Console running each.
I have a Main Identity and two Alternate Identities. I have them configured so that when I launch the first instance of Console, the Select Identity...

Screenshot-2020-12-23-102349.jpeg

Just off to the right of the waterfall is a narrow vertical window where you can adjust the window and leveling for the waterfall. At the top is an auto button. As I change bands I hit the auto button to see the...

Is there a way to remove the 'bias t on/off' button?

I'm using an RSPDX, V3.0.26

Hi, when using the frequency database I select a frequency, and SDR Console tunes to the frequency but the screen that displays the frequency does not change to the new frequency from the database. I attached a short video.

Edit: I have posted a...

The beacon offset is written into a CSV file. The maximum number of lines seems fixed to 10 000.
Can this number be changed by the user or is it fixed in the code?
The offset is written in time intervals varying between about 2 and 20 seconds. Can...

Introduction

Let me cite the lyrics in the first lines of the first tune on side 2 of the B,S & T album B, S & T 3 (1970).
Some of you might remember this album.

I have been kind of active here with quite a few posts recently. You might have seen...

Hello, Simon, could you or anyone please help with understanding the BugTrap dialogue buttons?
Like, presumably you have to SAVE before CLOSE if you want the dump?
I'm prompted to ask because after SAVE I tried PREVIEW but BugTrap never responded...

Are the stand-alone tx/rx windows scalable ? In other words, can they be scaled down to show the entire panel without cutting off the bottoms as shown?

I am trying to playback a I/O recording made with other software, HDSDR in this case. When I go to the select recording page it shows the recording with the correct duration but incorrect size. When I attempt to playback the file it will only play...

I am using the satellite tracking window in Console to receive WX satellite images. I noticed there is a rig control window on the sat page but I can't get it to connect with my DUOr. I have tried Omnirig and VSPE pairs but no joy. What should I...

Hello Simon,

I'm observing a strange and not reproducible behaviour of the Geostationary Satellite Beacon View. The issue is visible with 3.0.26, but I already observed it with previous releases as well. The effect seems to be independent of the...

Can someone explain this to me? I constantly get a difference in frequency between SDRconsole and my DUOR. It's off by 45 Khz, but if I tune to WWV at 10,000 it's dead on. Only seems to happen in the broadcast bands. How do I correct this??

Hello Forum,
I am very new user of SDR-Radio Console. I started a few days ago with 3.0.24 and using RTL-SDR dongle successfully.This morning I installed 3.0.26 on top of previous version, but seems to crash. So my question is do I first need to...

Version 3.0.26 32 bit won't start, reports missing files:
mfc140u.dll vcomp140.dll vcruntime140.dll

I reinstalled V 3.0.24 32 bit and that version works ok.

I did the installation/reinstallation twice to be sure a microsoft update hadn't screwed...

Hello.
This problem is not about recent version. I was having the same problem with previous versions also.

I have latest version of sdr console right now on windows 10 64 bit.
2020-12-14_23-02-28.png is the rtl-sdr model I am using.
When I start...

Screenshot-2020-12-15-061341_LI.jpg Just installed 3.0.26 and IF Display isn't symmetrical around 0 anymore.

This is probably a really trivial matter, in which case please quickly send me packing :D.

Screenshot A (LOWER) is a clean SDRC window.
Screenshot B (UPPER) shows an extra border just below the title bar (near the top of the menu tabs) and...

Recently I did field recordings over three nights with an Airspy HF+ Discovery and SDR Console v3.0.24 to capture non-directional beacons in the <500 kHz spectrum.

The first two nights, the bandwidth for the radio and recording were both set to 384...