It's all about the Software

Greetings, I have configured omnirig and xiegu g90 with sdrplay and jtdx, when I transmit with jtdx sdrconsole does not detect tx, but if I press the ptt on the microphone it detects it and mutes the sound, the only way I got it to work is by...

Firstly, I want to congratulate you on this magnificent software! And thank you!

I got a good connection between my old Ft450d and the SDR Console. However, whenever I try to set the radio to USB Data it reverts to USB and so I cannot use the...

I have moved to RSP1A, but the behaviour is always the same, issues with this syncro in External radio when tracking is active. why the spectrum is freezed? why without syncro or syncro used for qo-100everything is working?

Radio=>SDR tracking only...

Hi all,
I'm running SDR console with a sdrplay duo, omnirig and a ic9700. In using the ic9700 on satellite mode and I have everything synced up except RIT. I have selected rit in external radio settings but it never shows on the external radio...

I am fairly new to SDR Console, have it working with OmniRig and my IC-7600. It seems to work very well and is mostly intuitive. CAT works, follows along with my 7600 when track is selected. But that is only for my VFO A. How can I get VFO B to...

Hello,

I have set up here a panadapter with ic-756pro2, with the RTL-SDR on the 1st IF freq.

I have a few issues: when I'm changing frequency with the radio vfo the spectrum update looks slow and not fluid at all. I don't understand the reason...

I was not satisfied with the Noise Reduction and Noise Blanking Performance of the ICOM-7300. The Noise Reduction and Noise Blanking performace of SDRSharp impressed me (thanks Joanne).

The IC-7300 has a USB IF output where the the IQ Output as...

I searched the forum with no results. Can SDR Sharp control this device? I would like to use it as a classic SDR receiver with software other than Expert Electronics. Thank you for the information.

Hi,

I am temporarily using an RTL-SDR V3 dongle while learning about SDRC. It basically works but the external receiver window always shows Port Busy. Is this a problem? The radio is a Kenwood TS-590S and the software is DXLab. I am using the basic...

Hi
I probably forgot a parameter in my SDR Console setup using a RSP1A and a Yaesu FTdx via Omnirig.
At the start of SDR Console the «External Radio» window starts automatically and shows the frequency of the TX from Omnirig as expected but the...

Hi guys, I haven't used the software with ELAD FDM DUO for a while but I can't go to TX and not TUNE for the agreement...I configured the audio input and output but nothing....thanks.

ok audio RX

I have IC7300 via pandapter, I connect SDRplay receiver.
Everything is great, but the Signal meter readings on the SDRconsole are highly inflated relative to the IC. The reception level is the same, is there a way to lower, adjust these values?...

Hello.

I'm running an identity for QO-100 that has a SDRplay RSP2 Pro as receiver and an FT-897 as external radio.
When tuning directly from the FT-897, everything works fine and the frequency on SDR Console is changed to the same I handled on the...

Hello

I just wanted to use the SDR-Console for 80m with the Kenwood TS-480HX and for QO-100 with the FT-857.

Now, when I save the upconverter-offset (10057 MHz) for QO-100 in the FT-857 identity, then this upconverter-offest-setting is also used...

I use SDRC with an SDRPlay receiver as panadapter for an FTdx3000. The system works beautifully, but only tracks one VFO.

Is there a way to have VFO A on the radio control one receiver in SDRC and VFO B another? That would provide an excellent dual...

Hello everyone,

I am having difficult time configuring all the offsets and tuning the RTL-SDR receiver to work with a FT-1000D with it's IF output (73.620MHz).

I have control established of the transceiver to sdr console, I find the scrolling...

I have a few radios with IF taps fitted - FT-857, FT-847 etc. I run external radio with various SDRs. I really like the setup.

Unfortunatly the panoramic output isn't linear around the centre. I'm not sure if this is experienced by many, but I see...

Hello,
I'm using a RTL-SDR as panadapter on my ic-756p2.

I have found several anomalus behaviour with External radio mode:

1) zoom level rest each time frequency is changed by radio vfo, the zoom level should be competely independent.
2)...

I have a few radios with IF taps fitted - FT-857, FT-847 etc. I run external radio with various SDRs. I really like the setup.

One setting which I find a little frustrating is the bandwidth selection within external radio. I have it set to the...

Hello.

I've got an issue when transmitting while External Radio is active.
It seems the SDR Console detects external radio tx through CAT then mute and disable waterfall but the Auto Mute is disabled.
The issue happens only if External Radio...

Is it possible to route the USB output from the Icom IC-9700 to SDR-Radio?
If so, can someone point me towards instructions for doing it, please?
Thanks - Dave (G0DJA)

OK, I'm new to SDR Console, so the answer may be hidden away in the documentation, but I can't see it, so please forgive me if it's there...

I'm using SDR Console with an SDR Play RSP1A as the second receiver and enhanced panadaptor for my IC-7300....

Dear Sir
is it possible to add support for new omnirig v2.1 ?
is it can support 4 rig and poi time can less time 100ms (20ms) i think it will reduce time when do the switch from satellites RX/TX
because sometimes radio no response when press both...

I have the TS-990S transceiver into an SPE amplifier. This is handshaking with
SDRC via OmniRig. SDRC is v3.1 and OmniRig is V1.16. The SDR is an Airspy HF+ dedicated
as a panadapter.

Strange, but something has changed, and I can't quite figure it...

Update: As of today, I have abandoned HDSDR & HRD. Now using SDR Console 3.0.27 and all is working except I cannot get External Radio option under view pane within SDR Console to take and display within DSP window pane, even after re-boot. I am...