It's all about the Software

Hello,

Been quite a while, so please put up with a very basic question.
Incredible softtwre program.

Am using with an Icom R8600.
In the radio's memories, I have stored about 20 Groups, each with a load of Channels

SDRConsole locks the radio up,...

a friend of mine use sdr console and ic-9700 as external radio with 70cm
the offset on external radio iss 10057
rx works perfectly, but if he send on 432.700 he hear himselv on websdr on 10489.700.but never see his signal at waterfall at 10489.700...

I'm converting my ham radio computer usage to include SDRC as either the main receiver or as a panadapter. My Icom 7300, the External Radio will always be my transmitter. I've run across a weird thing. When running JTDX or WSJT, if Tracking is...

Oops, posted to wrong forum. Text moved to External Radio.

I have another post on the forum regarding the same issue, but specific to an IF frequency question. I'm confident that I am using the correct IF frequency and this question is more general. I'm experiencing extremely low voice volumes. The sound...

I have posted this message on the Kenwood 570 group on Facebook but I thought that I would do the same here as it may be a software rather than a hardware issue.

I'm attempting to set up a panadapter display using an RTL-SDR dongle and SDR...

Hello folks,

Apologies in advance if this is a simple fix but I've failed to add an external radio to Console.

I have followed the instructions;

View-More Options-Enable External radio- Then restart.

Its the restart is where I have the...

Hello. I'm still a beginner with SDR programs. I would have asked if I could use the Yaesu FTdx5000 radio as a PAN adapter with SDR Console 3.4. I would be grateful if someone could give advice on how to do it. My configuration is FTDx 5000...

Greetings
For several years now, I have had solid performance and enjoying SDR Radio point and click capability with the Kenwood TS-990S / Airspy HF+ Discovery and the External Radio capability (thru OmniRig, of course). This is thru the LAN and...

Anyone here use SDR Console with Malahit DSP2 radio? What is your experience with that combo?

I greet everyone. I have the ts2000 connected to the sdr console via omnirigs, it works fine on the frequency changes. The connection is made via if 75925. and it goes to an rsp1a. as for the frequency, if I hear and see that they are talking, I...

I have moved to RSP1A, but the behaviour is always the same, issues with this syncro in External radio when tracking is active. why the spectrum is freezed? why without syncro or syncro used for qo-100everything is working?

Radio=>SDR tracking only...

I'm an old timer of 45 years on amateur radio so this stuff is new to me. I would like to know what I need to get my Kenwood TS-59SG and HackRF One SDR to work to decode FT8 and display the FT8 also what other software is needed to work FT8 on the...

Hi, I am trying to use SDRconsole as a panadaptor with my Kenwood TS-590SG. The rig control via Omnirig works successfully with SDRUno. With SDRConsole there have been a few times when it worked, but most often I get port busy . No clue why this is...

Hi,

I'm about to buy an SDR, and I'm interested by the Pluto+.
But I also found other alternative like LibreSDR, which seem to be similar (but with a better FPGA), or even less known ones like the GeekRF One (and if you know others, don't hesitate...

Hello,
I just received my LibreSDR and tested it with SDR Console Version 3.3 build 2848 Ethernet connection.
RX, works well without any problems.
TX, no signal out of the LibreSDR.
LibreSDR is booting from SD-card (SD-card JT 2024 02 03)...

Hallo SDR-Console Users,

I use the SDR-Console V3.3 and an IC 9700 70cm + Transverter for Uplink. The frequency the console sends to my IC-9700 is 500 KHz to high on all Frequencys in the ssb part of the q100.
Changing the tx up frequency in the...

Greetings, I have configured omnirig and xiegu g90 with sdrplay and jtdx, when I transmit with jtdx sdrconsole does not detect tx, but if I press the ptt on the microphone it detects it and mutes the sound, the only way I got it to work is by...

The External Radio tracking (with Icon IC-7100) worked well for a few days.

But it recently has not been working. The ? screen shows Omnirig (Version 1.20) Not Responding.

I have 2 rigs selected on Omnirig:

Rig 1: IC-7100
Rig 2: IC-7100e4-DATA...

Hello,

Using the latest (I think) version.

Using with an Icom R8600

Tunes the radio just fine, and shows the ANT selected, and the tuned freq., from the program on the radio's display as it should.

But, cannot get it to show on the radio's...

I have Console connected to my IC-7100 as external radio and an RSPdx as the SDR receiver. I also have an MFJ-1708B SDR TX switch in circuit to use my 7100's antenna for transmit (only a 2 meter for now).

Most everything seems to work ok except I...

Is there a How To to enable Win4Icom rig controller to play nice with Console plus my IC-7100? I already have the 7100 connected as an External Radio in Console in addition to my RSPdx via OmniRig. New Consle user; like it a LOT.

Firstly, I want to congratulate you on this magnificent software! And thank you!

I got a good connection between my old Ft450d and the SDR Console. However, whenever I try to set the radio to USB Data it reverts to USB and so I cannot use the...

Hi all,
I'm running SDR console with a sdrplay duo, omnirig and a ic9700. In using the ic9700 on satellite mode and I have everything synced up except RIT. I have selected rit in external radio settings but it never shows on the external radio...

I am fairly new to SDR Console, have it working with OmniRig and my IC-7600. It seems to work very well and is mostly intuitive. CAT works, follows along with my 7600 when track is selected. But that is only for my VFO A. How can I get VFO B to...