It's all about the Software

Hello,
I'm using a RTL-SDR as panadapter on my ic-756p2.

I have found several anomalus behaviour with External radio mode:

1) zoom level rest each time frequency is changed by radio vfo, the zoom level should be competely independent.
2)...

I have a few radios with IF taps fitted - FT-857, FT-847 etc. I run external radio with various SDRs. I really like the setup.

Unfortunatly the panoramic output isn't linear around the centre. I'm not sure if this is experienced by many, but I see...

I have a few radios with IF taps fitted - FT-857, FT-847 etc. I run external radio with various SDRs. I really like the setup.

One setting which I find a little frustrating is the bandwidth selection within external radio. I have it set to the...

Hello.

I've got an issue when transmitting while External Radio is active.
It seems the SDR Console detects external radio tx through CAT then mute and disable waterfall but the Auto Mute is disabled.
The issue happens only if External Radio...

Hello everyone,

I am having difficult time configuring all the offsets and tuning the RTL-SDR receiver to work with a FT-1000D with it's IF output (73.620MHz).

I have control established of the transceiver to sdr console, I find the scrolling...

Hello

I just wanted to use the SDR-Console for 80m with the Kenwood TS-480HX and for QO-100 with the FT-857.

Now, when I save the upconverter-offset (10057 MHz) for QO-100 in the FT-857 identity, then this upconverter-offest-setting is also used...

Is it possible to route the USB output from the Icom IC-9700 to SDR-Radio?
If so, can someone point me towards instructions for doing it, please?
Thanks - Dave (G0DJA)

OK, I'm new to SDR Console, so the answer may be hidden away in the documentation, but I can't see it, so please forgive me if it's there...

I'm using SDR Console with an SDR Play RSP1A as the second receiver and enhanced panadaptor for my IC-7300....

Dear Sir
is it possible to add support for new omnirig v2.1 ?
is it can support 4 rig and poi time can less time 100ms (20ms) i think it will reduce time when do the switch from satellites RX/TX
because sometimes radio no response when press both...

I have the TS-990S transceiver into an SPE amplifier. This is handshaking with
SDRC via OmniRig. SDRC is v3.1 and OmniRig is V1.16. The SDR is an Airspy HF+ dedicated
as a panadapter.

Strange, but something has changed, and I can't quite figure it...

Update: As of today, I have abandoned HDSDR & HRD. Now using SDR Console 3.0.27 and all is working except I cannot get External Radio option under view pane within SDR Console to take and display within DSP window pane, even after re-boot. I am...

Greetings to all, and sorry if I'm stupid .. I have this problem, with the use of the external radio module ( SDR console )
I use a Yaesu ft1000mp mark 5 Field and connecting the radio with SDRPlay or an Airspy hf, the connection between SDR console...

Can someone help me fix this issue? I have Omnirig v1.20 and version 2.1.0.0 installed in two different areas of my system

Thanks for your help.

SDRC is nearly the PERFECT program for working satellites. The only place it is lacking is when running an external radio, there is no provision for having the External Radio Transmitter and the Internal Radio Dongle Rx track when running...

Dear Sirs,
Im using a RTL Stick and Omnirig as Panadapter on my FT-950 an it works very well.
Usulay the computer audio is turend off and I'm working only with the Waterfall BUT sometimes I like to use the Computer Audio special for weaker...

I downloaded the 3.0.26 version of the SDRConsole (v3) to update my 2.0.20.

All is running nice.

I wish to link the program to my Icom IC-7000 through the Omnirig 1.19 for freq CAT control.

Now my Omnirig are in well relations with MixW3, JTDX,...

Hi all,

I have a problem with frequency synchronization with SunSDR2PRO. Both SDR Console and EESDR are set to OmniRig. After switching on, the frequency is synchronized, but only once. The same configuration with the FLEX6500 works perfectly. Has...

Hello,

I have set up here a panadapter with ic-756pro2, with the RTL-SDR on the 1st IF freq.

I have a few issues: when I'm changing frequency with the radio vfo the spectrum update looks slow and not fluid at all. I don't understand the reason...

:)

Hi all,

I have a problem with SDR Console when I want to use my FT-817 or my FT-857 with external radio option. I receive the error message Port busy and/or offline . To cancel it and make the external radio working, I have to remove and reinsert...

Hello All

I -think- I'm consistently seeing a buggish interaction between SDRC (3.0.22) + WSJTX (2.1.2) + Omnirig (1.19)

whereby SDRC autonomously changes the rig from DATA/PKT to USB (Upper SB), FT817 w/FT817 rig selection

Steps :

1. start...

Hi
I tried to connect Ham Radio Deluxe (HRD) with SDR Console (SDR) with no success. Then I monitored the traffic on the COM ports and saw: com6Monitor1.xlsx
After a request of HRD on the COM port SDR sends its answers from a one-byte buffer. This...

After a struggle with consistent external radio port online status (and configuring Omni-Rig correctly),
I decided to go back and start from scratch, more or less. I would like to understand what the purpose/
requirements are for the check boxes...

Hi,

When using the external radio option is it fully integrated with SDR Console, e.g you can control mode, PTT, drive etc all inside the software?

Or is it just basic frequency synchronisation?

Thanks

Hello again...

got rid of the ftdx1200 and now have a ftdx3000..lovely rig..

trying to get it to work with sdrc as external radio.
no hope..(except for once yesterday, and i have NO idea how!!)

using serial to usb to pc.pc sees it and says all...