It's all about the Software

I had to do a lot of reading to understand filter choices and the differences between filters.
I think tooltips to advise the user on which filter to use would be very helpful.

I am sure that there are best choice filters to use for each...

Currently, whenever I change bands I have to hit the Auto button to see the best view of the waterfall. I would like to have that occur automatically when I change bands so I don't have to keep hitting the button.

Thanks!

So, I don't know the specific mechanism that would be needed for this, but I know it would be very useful.
The idea is that users can set up events in their operating system event manager and attach a command line script to run.
The script would...

Mentioned before, but thought this ought to be a new request.

The carrier-locked mode gives excellent results bringing a channel-dominant station into focus. At the same time, a co-channel weaker station tends to be masked. Experiments without...

Mentioned before, but thought this ought to be a new request.

Binaural results are better with IF bandwidth greater than about 2 kHz, so asymmetric passbands are not the ideal way to get rid of heterodynes from adjacent channel carriers (say, 1, 2...

Hello,

I would like to monitor DMR trunking system which has 8 physical channels (16 slots). Is it possible to expand number of receivers in the software from 1+5 to 1+7?

Regards, Kamil

Hello, Simon, hope your micro-break has done some good!

Your recent Open Next/Previous feature delivers more than I expected from reading the initial request - it operates on the sorted list (however that was defined) and starting entry , when you...

The 100% setting of the squelch scale is quite low compared to where the noise floor can be. On my RSP1A, with a gain setting of 5, IF gain at -35 and AGC off, on VHF and UHF the noise floor is around -80 dBm, which seems to correspond to around 90%...

Hi Guys,

is there a way to use the MPX output for more than just one receiver? I am currently using the SDR Console to rebroadcast 8 radio stations and bring them to a website via Icecast.

So I use the SDR console and 8 virtual audio cables to...

Wondering how difficult it would be to incorporate something similar to how HDSDR does it:

Capture.PNG

Thank you in advance,

Mark

Dear Simon,
Would it be possible to allow the selection of different TX and RX antennas with the Anan radios?
The reason I ask is that I have been unable to see how I can use the transverter TX and RX SMA options on the Anan Radios.
As many...

Hi Simon,

1. Your Worldmap program is mature now, can you add a Worldmap button next to the Frequency Database button?

2. Is it possible (when your in the mood) to make a connection between the freq. database (long/lat fields) and your Worldmap...

I use a tablet for sdr listening.
Sliding my finger back and forth on the screen to make small adjustments to the frequency is difficult.
Is it possible to add either
1. A scroll wheel in place of the waterfall contrast slider (on the right side),...

Hi Simon

Automatic notch filter it is not very powerful
it would be necessary to add the possibility of adding the manual notch, such as SDR #, winrad and others,
often reception becomes impossible when we have a signal within 3 KHZ.

Regards...

Hi Simon,

Now the broadband SDR's are slowly emerging, wouldn't it be nice to have the possibility to scheduled multiple data recordings not only one after another, but also overlapping?
This would open the way to analyse stations transmitting at...

Playing around in the MF broadcast band, looking out for winter DX , I'm often looking for weak carriers on Region 2 10 kHz channels and trying to ignore the 9 kHz carriers. That sounds easy to do visually, but does get a bit complicated as you...

Hi Simon.
It is not possible to fully utilize the 1333 kHz BW in the AFEDRI Net in the SDR-server as the maximum BW choice for WAN is 1000 kHz. See attached screenshot.
Would it be possible to have a higher alternative for WAN-interfaces than the...

Hi,

Would it be possible to have the waterfall saving one line every xx seconds to a jpg / bmp file ?

I do record 6 - 12 - 24 hours with 6 MHz bandwidth and I can use the data flie analyser to generate the corresponding waterfall to check for...

Hi Simon

I managed to synchronize between the SDR Console and my transceiver. Theoretically it works ok. What I receive in SDR can also be heard in my transceiver. When you click on the screen, the transceiver moves to the correct frequency.
But...

Hello,

I am considering making an Arduino based MIDI interface to use with SDR Console. As far as I can tell it's assumed that Tx Drive, Gain and Proc are assigned to buttons. Is it possible to use potentiometers for these functions?

Thanks

I would like to see a few more Mic setting buttons and be able to re-name them.

The satellite Automatic Schedule sometimes does not switch to the frequency for the next satellite on the schedule. Sometimes it switches to the frequency defined for the satellite using Organise but sometimes it does not switch to that frequency....

While scrolling through recordings, especially longer ones on a large screen looking for activity on a certain frequency, it would be handy if one could enable a vertical line marker (or a pair of dotted lines in a similar style to the lines used in...

Hello,

Might it be possible, or practical, to have the time for start, stop, etc. in
the Recording App be shown additionally in GMT, rather than just local ?

Both ?

Thanks,
Bob

There are times when I'd like a much faster FFT response, with no averaging. Even when the smoothing hang is set to minimum & decay set to maximum there appears to be ~250 ms or so of spectrum averaging. Same if I use the weighting option & move all...