It's all about the Software

Hi Simon,
Using Console 3.3. When using QO-100, I would find it very helpul if the Rx audio could be muted automatically when the Tx button is pressed. This would make for a much quicker change-over. Perhaps you could incorporate a tick box 'Auto...

Greetings.

Can I make another suggestion re: MIDI?

Can the Data Playback functions be added to the possible commands that can be mapped to MIDI?
Would only need to be the START, STOP, PAUSE, BACK/FORWARD (by x interval as previously set).

Being...

Dear Simon,

to build a full radio with pluto (may be on a raspberry...) the only feature we need is the ability to move RIT via MIDI command.
It is necessary, for example, on the QO-100 where the correspondent is not always isofrequency and SDR...

I got a new laptop that runs Windows 11. However, the key that was the right Ctrl key is now the CoPilot key. I find this very annoying. I want the Ctrl key back.

The result of Googling on this issue results in the suggestion of installing...

Would it be possible to add support for 2MS/s transmissions (repeater outputs) please?

very best regards,

Justin - G8YTZ

Is it possible ( pretty please) to add the facility to cycle through the filters with a MIDI device as defined in the current mode selection?

As I posted on the IO forum, I find the incremental change of 50hz much too low when in BFM mode.. what...

Hi All,
I have a request regarding CAT command to select a specific Receiver RX1,RX2,etc...
With FA command I able to set frequency *FA, FB,FC, etc ) but I can't enable a specific receiver.

I only see in MIDI configuration the possibility to select...

Hi ,

is there anything going on for the Red Pitaya 16 bit ?

Kind Regards

Pat

As posted to the IO group a little while back, but putting it here in case it gets lost....

I have used the Memories a lot more recently, for example to put beacon frequencies in, or for using as a scratchpad during openings.

I find it's better...

Hello,
in the following groups.io discussion it was already asked about flip mode implementation for better rotor control.

I now wanted to put this feature request in the correct location.

The gist is as follows.

For rotors supporting 180° of...

how about feature that at the click of a button a text or xml file so that the whole configuration is easily attached to a post.

Thank you for reading this.

Amongst other thing, I use the software as panadapter, synched with my HF rig. The system works like a charm, but I find it annoying that any time I change band on the RTX, the amount of spectrum I see on the panadapter...

I just changed from ICOM 7300 to ICOM7610. On the 7300, I use a IF tapping card to get the signal to a RSP1B SDR, itself piloted by SDR Console and it works so well. On the 7610, I was hoping to use the IQ signal from ICOM that work with HDSDR but...

Hi,

to my knowledge the actual Aaronia support is limited to the v6 full version , not the ECO. So I wonder if it is planned to support also the ECO, as this is for sure the radio that will be bought by many hobbyists.

I own the ECO in RX/TX...

With regard to the Frequency Database feature, it would be nice, due to my aforementioned laziness, that it might somehow highlight broadcasts that should be on now based on the current time so as to not have to sift through a sometimes long list....

SDR console is my favorite program for controlling SDRs, the latest addition is a ZynqSDR/LibreSDR which comes in a CNC housing. This SDR it is equivalent to the PlutoSDR, in fact the Pluto+ with 2TX and 2RX but it requires modified firmware. What...

SDR Console v3.3 still needs MS Visual C++ 2010 and 2013 Redistributable kits.

MS Visual C++ 2010 and 2013 Redistributable kits are end-of-life products (EoL):

Only the MS Visual C++ Redistributable for Visual Studio 2015-2022 is supported by...

Hi,

I have been using sdr console for years now, but I think it would be great if it could support transmit for DG8SAQ/PE0FKO/SoftRock based radios (currently there’s receive support).

This will enable owners of peaberry pi, multus proficio and...

I have long used and enjoyed the SDR Console, and believe it's one of the most featureful and capable out there.

It's just a pitty that I cannot transmit with my homemade and kit-made SDR radios based on hard/soft rock which use sound card input as...

Hi,

It would be useful to have the squelch command (the equivalent of the SQ command in the official Kenwood TS-2K protocol) supported in the serial cat protocol to be able to manipulate the value (read/write) in the same way that we have the AG...

hello
will be great if you can add a SA44B — 4.4 GHz Spectrum Analyzer

do you thing it is possible
thanks
and by the way i love sdr console

A little wish, big effort? But asking anyway...

Hovering the mouse over spectrum or waterfall displays a vertical tuning bar with centre and bandwidth limits plus channelised tuned frequency.

An optional mode could be cross-hairs. Vertical to show...

Is thera any change impelement TCI Protocol for CAT. TS2000 with Omnirig is one kind of pain if you use up / down converter, example LOG4OM cant go QO100 frequencies, its show offliine.
If you go under 2ghz its start show freq. As far i know,...

Greetings all @ SDR-Radio.
My request is for a pop-up Deviation Meter, similar to the pop-up signal strength meter.
It would need to be able to read up 100kHz deviation depending on what mode, eg NFM, WFM, BC-FM is in use.
I use your program along...

Hello,
I've been using your software with my RadioBerry that has started to gain traction again and am curious. Is there any possibility for a release the includes a dark mode for the window colors? With the customization of the waterfall colors, a...