It's all about the Software

Oops, posted to wrong forum. Text moved to External Radio.

Hello,

Will blame the following most basic question
on old age now. Great excuse for most anything.

Could someone please give me the link to the latest
version I should download ? (any reason for a very basic contemplated user to download a Beta...

I have a small linear for working base station.

My portable setup is now modular, based around a G90 and an RSPDxR2 SDR and Console 3.4 it works amazingly well all held together with Omnirig.

/P I'm out and about running from 1W to 10w in the...

Sorry all,
So many questions.

I have noticed on higher frequencies the VCO from my TX Radio in this rig (my G90) is to the side of the listening frequency on 20m and up.
Tuning to a higher frequency is inaudible, however as you tune down the...

Dear G4ELI,

I made a silly post a while back, and then I bought an SDRplay and SDRSwitch.

V3.4 saw the SDR and ...setup Omnirig....and my mind was blown about twenty minutes later as I pulled in tiny signals and ramped up DSP ...

This is the...

Hello:

Perhaps it is just me, but I am having trouble figuring out how to keep the freq span in the display after zooming in. The default seems to be 0-100 khz. I've tried all kinds of things to keep the span coming up every time I go to that band,...

Sorry if I might have gotten this wrong,
But I had the impression that console could be used to do soundcard I/Q Conversion and could do bi directional sync with Omnirig ..

Yet I am stuck on radio definitions ...

It seems I'm mistaken?

I have a good signal on my FM station, but I am experiencing hissing noise in the background.

Is there anyway I can remove the noise. I have tried the noise filters, but it doesn't seem to make any difference.

Thanks in advance for your help.

Hello Friends,

Anyone of you use the card like this SDR 70 MHz-6 GHz Zynq7010+AD9363 with the SDR- Console software ?

Is it possible to manage the 2 RTX channels independently ?

I would like to use it as an RTX driver for an HF radio with IF at...

Just a quick note to say:
Thank you Mr Brown for the free software. I made a donation last year and have just done the same a week ago via your donations page. I must just say how much I appreciate the effort and hard work that has gone into SDR...

Good morning everyone.
After upgrading to SDR Console v. 3.4 from 3.3 long time ago ( now I use the latest one ) I found immediatly a couple of anomalies of which the most annoying is the distortion of the audio transmitted via Adalm Pluto. I use...

OK, spent some time this AM doing A/B tests using the Nooelect Flamingo AM BC Filter.
The setup is:
Inverted L antenna, active 4 port multicoupler, two Airspy units with same firmware, two copies of SDRC running side by side. The copy on the left...

Sorry if this has been raised before.
I have a hard drive folder containing one set of chained recordings made by SDRC. They were found in an internet archive of HamSCI files.

The first 30 or so had been omitted, so the filename sequence begins...

While investigating the QRM generated by a local AM BC station that jumps to 5KW at local sunrise, I found the following action with the Radio Airspy Discovery using my
normal settings of:
AGC High (or low) doesn't matter
Attenuator OFF
Pre Amp OFF...

I have another post on the forum regarding the same issue, but specific to an IF frequency question. I'm confident that I am using the correct IF frequency and this question is more general. I'm experiencing extremely low voice volumes. The sound...

I have posted this message on the Kenwood 570 group on Facebook but I thought that I would do the same here as it may be a software rather than a hardware issue.

I'm attempting to set up a panadapter display using an RTL-SDR dongle and SDR...

I'm new to using SDR radio / software. I recently purchased a HF+ Discovery, and running it with SDR Console (SDRC) v3.3 I recently downloaded.  It's working great, but how do I know if I'm leveraging the proprietary noise reduction algorithm...

I think there is a problem with applying a frequency calibration correction with the SDR receiver (a Zyncsdr / Libresdr) listening to the 70cm band (433.5 to 434 MHz) while the signal comes from a QO100 downconverter running between 10489.500 MHz...

Is there more information about MAP65 Support in newer SDRConsole beside of whats in the SDRConsole itself

To be able to use SDRConsole with MAP65 for X-Pol (H/V) antennas it need support of two coherent 96KHz I/Q streams coming from a Dual...

I would like to use sdr-console to tune into narrowband signals acquired by a Casper SNAP board.

So I'm looking for documentation on a suitable IQ data stream that sdr-console recognizes. The SNAP is set up to easily stream UDP, so I'm looking for...

Dear Friends

I set my Lime SDR as shown in the photo to have an IF at 150 MHz.
In transmission it works perfectly from 14 MHz it transmits at 164 Mhz,
while in reception at 164 MHz I receive nothing.

Where am I going wrong?

Thanks 73 Arnaldo...

Subject: Assistance with Ingesting Raw IQ Data from SDR Console across LAN into Python on another PC

Hi, I’m attempting to ingest raw IQ data output from either the Data Repeater or the SDR Server in SDR Console using Python. I can successfully...

Hi Guys,

I'm a long time radio builder, and I'm planning a hybrid analog/digital RTX.

I am testing RF output with a spettrum analyzer using SDR Consolle with LIME MINI USB on the HF band TX (setting 3 MHZ Hf-TX)

In some bands, even if they are...