It's all about the Software

Hi,

I'm out of ideas, my pluto has an ethernet adapter and has worked through all versions of SDR console until the version bundled with the SDR television.I created new definitions as described but the program reports back no Pluto found at the...

Hi all
Just joined the forum !
Using SDR Console version 3.4, and trying to configure it to do FT8 with MSHV.
When I set line 1 for transmit and for receive, the Pluto will go transmit erractically (with MSHV not opened). Bursts of emissions,...

Good morning everyone.
After upgrading to SDR Console v. 3.4 from 3.3 long time ago ( now I use the latest one ) I found immediatly a couple of anomalies of which the most annoying is the distortion of the audio transmitted via Adalm Pluto. I use...

How can I use the Pluto Plus ethernet port with SDR console?

Hello,
I haven't used my Pluto D for two months, when I start the SDR console (3.4) I usually, but not always, get the display below. What can be the cause?
Conn.jpg
73 Detlev

Hi,
Apologies in advance if this is a noob question.
I recently purchased a Pluto SDR and am trying to test it on a local FM radio station (104.7MHz).
I’ve changed the config of the SDR so it now operates from 70MHz to 6GHz, so it’s in range (set it...

Hi All

I am trying to find a way to solve an issue I am having,

My setup is a Adam Pluto Controlled by SDRconsole and I am running JTDX and JTsync on my PC

Now when I sync the time on the PC to the server I am seeing the FT8 stations have a dt...

Hi All

I am trying to find a way to solve an issue I am having,
My setup is a Adam Pluto Controlled by SDRconsole and I am running JTDX and JTsync on my PC
Now when I sync the time on the PC to the server I am seeing the FT8 stations have a dt...

Hi all, now running on v3.4 but the tx meters are absent except the ALC meter, which was also the case on 3.3. It's not a major problem but it would be nice to see them :-)

Regards,

Roger G8VLR

Hi all,

I have run my QO100 setup for nearly a year now. The heart of the unit is a Pluto+ which works very nicely on v3.3 (2993) with my Jabra evolve usb headset. I decided to try an update to the latest version (Feb 2024) and sound from the...

Could someone confirm the latest Pluto Plus Firmware version for me please. I believe from the BATC and Github it is v 0.33, but just wanted to check.
I am currently on v0.31-dirty and it has a few bugs on it.

Thanks for your assitance
Bob G4MWR

Is there any way to get the full 20Mhz bandwidth on receive using a Pluto

Thanks Dave G4IUG Ex G8EAO

Hi,

On SDR-Console V 3.3 when I try to select Hermes Lite 2 in the Search option, I am given the below option

-> Default
-> Extended
-> Fixed Address

But when I select the option of PlutoSDR in the search option,I do not find any of the options...

Hi all,

This must be something I am doing wrong, as I have searched the forum and find no mention of this issue.

SDR Console 3.3 / Pluto Plus / CN-0417 Preamp / DX Patrol 12w Amp.

When I first power up the Pluto+ and run SDR Console I can’t get...

Hi friends! Sorry for long read, but it worth it.
Things were looking good when I installed the latest v.3 Console on a Dell notebook Win10 and connected Pluto radio (Libre SDR) directly via LAN, had some QSOs on QO-100, but then I found out first...

Hi All

I am trying to get my Pluto and SDR console to TX CW,

What I find is that if I set it to USB I can TX using MRP40 and of course RX is okl

But when I set the Pluto via Console to CW I can not get the audio from MRP40 to TX from SDR Console,...

Hi All,

I've been using Pluto with Sdr Console for QO100 for a couple of months now and thought I had an issue with tx drift, but it turns out that although beacon lock appears to to function, over time the frequency drifts by as much as 2KHz. I'm...

Hi all,

I'd like to use a footswitch with my Adalm Pluto on QO100 for tx/rx switching. Is it feasible and if so how?

Thanks and regards,

Roger. (G8VLR)

Hello, I have a problem using the Adalm-Pluto together with the SDR-console for QO-100 communications. So far, everything works fine except of full duplex. Anytime I switch from RX to TX the console waterfall becomes completely noisy and no signal...

Good day all.

The Pluto Plus comes native with two receivers and two transmitters, each with its dedicated antenna connectors.

SDR Console at the moment sees only one. If I open a new instance of the software and try to use the Pluto, I am told...

Hi,
I'm a newcomer to the Pluto and have just received one today. Got all the drivers and it seems to have installed ok. I can see the Pluto in the device manager.
Start up SDR console, add the radio, set the definitions, and hit start.
Everything...

Hi! First of all, I must say I am enjoying the program a lot and am using it primarily for receiving from QO-100 and other sats. Simon, thank you very much for the great software!

I am having troubles to fully zoom in to see the received signal in...

Hi, I'm new to this forum and I hope I'm asking the right question on the right forum. In order to use my Adalm Pluto I have to download and start the program SDR Console (64bits). Downloading is not a problem, and after downloading the program will...

Welcome, dear Simon!! Please help me with the problem of displaying 10ghz on my console... The converter settings are made and displayed in the window, see the screenshot, but there is no display of the fundamental frequency... what should I do or...

Hello.
I try to run my Pluto over a VPN, but this VPN is a bit slow, so there is no continious sound out of the Console. Is it possible to reduce the bandwidth/samplingrate or what else, to get a smaller datasize?

I hope for any help.

'73...