It's all about the Software

Hi,
I have a Pluto running with SDR console v3, ASUS pc and win 10, trying to get a QO 100 station together.I have the RX working ok, but I cannot get any TX. The console TX DSP panel all seems to operate as it should, but no output from the Pluto...

See this link .

For the time being don't use FW 0.32, stay with FW 0.31.

Hi,
Apologies in advance if this is a noob question.
I recently purchased a Pluto SDR and am trying to test it on a local FM radio station (104.7MHz).
I’ve changed the config of the SDR so it now operates from 70MHz to 6GHz, so it’s in range (set it...

My notebook (ASUS X64) runs with Win10 and the latest update, as does my Lenovo PC.
My Pluto is connected to the PC and the notebook via LAN.
Everything works fine with the PC, but with the notebook I can only receive QO-100 signals.
With TXon +...

Can anyone tell me what signal level to expect from the PSK beacon on QO100 via Pluto and SDRC?

At the moment mine seems quite low at -112dBm or S2 but listening via the batc Goonhilly sdr it is about s9+10db. I am using a 90cm dish and 0.1 lnb....

just a test
EXT_REF.jpg
can be deleted later
:D
greetz sigi

Hi

With the latest AD firmware (0.32) SDRC does not control the GPO pins on TX but with the F5OEO DATV firmware it is ok.

So, two questions:

Is there any reason not to use the F5OEO firmware?

Will SDRC drive the GPO pins on TX in the future on...

Hello,
is there a timepoint known when a CW Generator for transmitting is available ??

Or is an Alternative Solution known ?
tnx Information

73 es HNY 2021
herbert
dl4sdr

Hi,

I’d like to ask for the following additional feature / option :

But first a description about what I did:

I developed a small add-on board for the Pluto which delivers some pretty accurate 40Mhz to the Pluto (Tailor Winfield VCTCXO) – I...

Hi all
I would like to help me, how to place Adalm Pluto in windows 10 home.
Thanks

Hello all,
Pluto SDR Console V3.025 for QO-100. Audio is noisy and has a lot of distortion when monitoring audio (Monitor , RX in the Transmit pane) . It used to work fine .
Windows 10, I7 PC
Any ideas ?
73 jacques F6BKI

Hi

I am new to Pluto so this is probably due to something I have not understood.

The gain of the main receive screen and the gain of the geostationary beacon screens are different.

When I first start SDRC and want to lock onto the beacon it is...

Simon asked to post the issue here, I did already post it a few days ago in the Test Team forum.
Please post this problem in the Pluto forum if you haven't already done this, add a full logfile. From memory the maximum allowed value may be 49 but...

I have just modified my Pluto for external (40MHz) reference, taking care to get the level correct. All seems to be working fine, apart from a frequency offset that I (eventually) cleared by setting the offset to zero (it had a stored value,...

Hi All

Now that my start/stop problem is solved (thanks excellent Forum!) I have another issue to bother you with.

Same Pluto, but older lower performance PC.

The issue is a spectrum/waterfall that has lower bandwidth than expected. As far as...

Hi all.
This morning DHL delivered my ADALM Pluto in Justin Peng's incarnation (in the same package as my RX-888).

After installing the USB driver from Analogue Devices Git-hub SDRC 3.0.25 of September 28-0716 found it OK.

It has the 70 MHz...

I recently had my venerable laptop degrade to the point where it is useless. I bought a new one. Both are Dell XPS-15s, running Windows 10, 64 bit. I had SDR Console 3.0.21 on the old PC, and installed 3.0.24 on my new one.
The old one worked fine...

Hi all.
Does anyone have any experience from this ADALM Pluto incarnation?

Good or bad experience?
Happy to hear about any experience with this Pluto incarnation product or the specific vendors.
Thanks in advance.
73 / Ingolf, SM6FHZ