It's all about the Software

SDR Console v3.2 for Windows 7 is locked by default

How to unlock it ?

Hovering over Program lock icon I get lock locked
When I click Program lock, new window opens with a message: Program locked
and Open lock icon to click
to unlock the Program...

How to upload screenshot of my SDR Console v3.2 ?

works for url address

SDR Console v.3.2 32-bit installed, Media-Tech usb RTL dongle installed, recognized, no signal at all (Windows 7)

Is there any way to check if any signal is received ?

RTL Dongle USB - unknown 20 -2000Mhz (drivers installed)

dBm meter set at...

Downloaded Zadig as advised, run in Windows 7, 32-bit
to update driver and Total Security 360 monitored 2 problems
and win usb driver update locked

I can attach photo.

thank you

darius

Media-Tech USB RTL dongle installed, recognized, no signal at all

any idea ?

small indoor antenna installed by default
no signal at all

RTL usb dongle donated by my friend
since another Media Tech usb dongle purchased a week ago was to short to...

SDR Console v.3.2 32-bit installed, Media-Tech usb RTL dongle installed, recognized, no signal at all (Windows 7)

Is there any way to check if any signal is received ?

RTL Dongle USB - unknown 20 -2000Mhz (drivers installed)

dBm meter set at...

Hello everyone,
Been Licensed here in the UK since the early 1980s and I have just started to get some interest back.

I was introduced to the RSP-1A which I use to listen with a long wire but the QRM around here is hammering me at S9 on 40 and 80m...

Hello, I recorded few hours of data using Data :: Record function in sdr console v3.2, signal from rtl sdr. Is there a way to speed up playback or generate waterfall with timestamps to see when was a broadcast on which frequrency?

An older (but still great specs) SDR...can I use it with SDR Console?

Hi,

I bought a nasa marine HF antenna at a boat jumble and would like to try using it with an RSP1 sdr receiver I got on ebay (link: sdr ).

The HF antenna is an active antenna so how do I go about connecting the two - are they even compatible?...

I have a new SDR Module I purchased from WISH.com via Store TINAMILY it has 5 SMA Antenna inputs and it covers from 10Khz to 1 Ghz but I don't know the brand or type it is so what definition do I assign it to use with SDR Console??? I am new to SDR...

Hello,
I would like to set up a remote receice site that has minimal resources. I need to use a Raspberry Pi 4 running SDR++ server and connect to it using SDR Console. Is it possible to connect to SDR++ server with SDR Console?

Thank you,
Larry

I saw this pop up when I was searching for a 16bit sdr looking for another kiwi / flydog sdr, never seen it before and cant find anything on the web about it seems rather new on the market, it does say SDR Console is supported, anyone know what BW...

Reluctantly admitting I need a quick solution to VHF/UHF operation for the summer and considering IC-7100 as a solve all for 6m/4m/2m/70cms until the day I can get my Hermes Lite 2 working with some older transverters I have. They all need mods of...

I am looking to use this online SDR but want to open it in multiple browser tabs, each tab set to a different frequency.
This is easy to do, but the difficult part is that I want to route the audio from each tab to a separate virtual audio cable...

I'm new to the group and will read past posts to see if I can find my answer, but wanting to know if RTL-SDR V3 with SDR Console to monitor shortwave down to 75 meter 3.995 is doable? I see signal on the waterfall, but cannot decode the audio....

Good Morning. I use sdrconsole v3 for almost all my receptions. Lately I tried to use sdrconsole v3 to receive radiosondes without success. The generated waveform does not allow me a good reception. I believe it is some configuration that is not...

Hello, friends...

I learned yesterday that one of my favorite DX tools (quite literally named DX Toolbox) has CAT commands implemented using the Kenwood TS2000 protocol and therefore can tune your receiver using SDR Console. It is not immediately...

Hello All,

I use Console since long time with SDRPlay devices (RSP1 and RSP2) with (almost) full satisfaction, apart the well know problems (ghosting, etc).
One of the big problem is the restriction to 8 - 10 MHz bandwith that can be received at a...

Hi there.
I have used an IOS App called WebSDR which appears to be an internet equivalent of the SDR USB + Arial option (?) in that you can tune in to all sorts of radio over the internet using the waterfall view.
As yet I know little about radio so...

I was on HF running FT8 and was noticing people struggle to copy me even when my signal was strong so I wanted to set up a monitor on my signals. At first I tried just running an AFEDRI with no antenna but I became convinced that the ugly signal was...

Hi,

The SDR I am currently using is the BladeRF Small Rev. 2 (x40). I'm very new to SDR's, therefore I apologize for my lack of knowledge if I'm doing something wrong. When I try to select BladeRF in the radio definitions the SDR Console returns...

Hi,

I've been looking for a spectrum analyzer sweeping software. Is SDR Console V3 able to take in a receiving signal and sweep across its frequency spectrum? If not, does anyone know of a spectrum analyzer sweeping software for the BladeRF? I'm...

Hi all,

I'm a new player and just getting started, so I'm sure just like the rest of you when I had my system set up I tried to listen to some FM radio stations.

I'm in the US so I tried looking for stations in the 87.8 to 108.0 MHz range but...

Trying to set the standing current at 1A on this amplifier kit. At about 240mA, the current rises uncontrollably to 8A. Temporarily connecting a diode detector to one of the transistor drains it detects 65v dc - oscillation. I've terminated input...