It's all about the Software

Goodmorning everyone,
I have implemented a CAT control with ESP32 and Encoder for VFO setting.
Is there anyway to select a receiver that I have create in SDRC ?
With CAT command FA, FB, FC etc.. I can set the frequency but is not possible to Enable...

Attached to this post is a SDR Console XML file that turns a MIDI piano keyboard into an SDR Console controller. Two octave keyboards are plentiful and cheap, and some may be more durable than DJ Controllers. I've set up all of the usable receiver...

Hello everyone

I would like to introduce you to a small project I am working on. I think that Simon's software is currently one of the most complete and I really appreciate the effort but I have always found it a bit difficult to manage the...

Hi everyone. I need to identify, using CAT commands, the currently-selected Mode of SDR-Console. I know how to use the MD; command, but it returns only numbers (that’s OK) but the same numbers are used for multiple but related modes (not OK). For...

Where in Console menu do I find comport setting options to sync Console with other radio apps?

I will be using com0com.

Hi,

I am trying to interface the SDR Console V3.3 with Log4OM2.

I am not succeeding to get the VFO & mode information to the Log4OM2 application.

Log4OM2 works fine with my FT991A.

An suggestions as to how to get this fixed?

Thanks
Ravi

I use SDR Console V3.3 with an Adalm Pluto+.

I want this to be seen as a radio by HamRadio Deluxe.

I created a pair on com0com (COM9 and COM10).

I set SDR Console to use COM9 at 57600.

I set HRD to use COM10 at 57600.

Nothing. No communication...

Hello.

I use SDR Console to pilot Adalm Pluto for QO-100 traffic. A question : Where do I connect the key to transmit in CW? And does it require a particular interface or configuration?

73 QRO de Michel F6GLJ

Good evening,
I would like to buy Tmate 2, but before doing so, I would like to know this: If by opening two simultaneous instances with ic9700 and ic7300 (I have panadapter in both Icom devices), can I control them both with only one Elad...

Reading the manual it recommends the Dencovi USB relay controllers. Will the generic USB relays boards work just as well?

I bought a HerculesDJ to control my radio and I did a few basic tests assigning keys and VFO worked fine. I stripped the HerculesDJ console down and removed various controls physically from the PCB before fitting the board into its new casing....

Hello.

Can SDR Console exchange CAT information through UDP or TCP?
I am running SDR console for QO-100.
To logging contacts I'm running a CAT software that reads the frequencies from Console and send them to logging software. All connections...

Hello guys

I am building a MIDI VFO with rpi PICO and I send simpel note on and note off on 2 different notes
I can register them in SDR MIDI map se picture, but i can ONLY tune UP when I send TUNE down nothing happends

So i wonder what is...

Hi all,
Yesterday I stumbled upon a page on the SDR-Radio site that described how to set up Virtual Audio Cables. Unfortunately, I didn't bookmark it and now I can't find it again.
Can someone point me towards where it is please?
Thanks - Dave...

I have a quantity of these units. They are HID and W10 recognizes them. Is there a way to add them to the USB choices?

Thanks

Jim

Hi to all,
I had the opportunity to test ARTURIA BEATSTEP controller as MIDI for SDR Console v3.1
arturia-beatstep-1780265.jpg
Very good impression during use, comfortable and excellent sensitivity of the controls, all the knobs are endless...

Hi, this is my configuration of MIDI: Hercules DJControl STARLITE, after some adjustments here is the setup that I am currently using, installed for a week so far it had no problems :roll:
Both the VFO and the x10 and x100 tuning are configured to...

Trying to get FT8 going with my HL2 SDR (not external radio) but for some reason not having total success. I did at some point have WJST-X controlling SDRC frequency for receive by selecting band setting in WJST-X but somehow I even managed to mess...

Hi, as SDR TX owners probably know already: function keys F5 starts TX and F7 starts Tune

I can recommend this USB foot switch, i use the right switch for TX and the left for TUNE. I bought mine on AliExpress.

r/Leon, PD3LK

Hi,

I have heard that this device is supported with SDR Console, could anybody share with me a way to setup it correctly?

Thanks,

I just completed a UI prototype using the CAT protocol.
This hardware user interface consists of a Wemos D1 mini lite ESP8266 board and an HN3806-AB-600N rotary encoder. Although not using WiFi, I used an ESP8266 D1 mini lite because it was...

I like many others I guess, use Virtual Audio Cable (VAC) by Eugene (Evgenii) Muzychenko for piping audio to and from SDR Console and other pieces of software.
Well just recently it has stopped piping the audio. This may have happened when the PC...

Hi, the IF command always seems to return 0000 for frequency step size... (current frequency is correct)
how to read frequency step size ?
Thanks

The midi output from the Pioneer DDJ-400 should be fairly standard but does anyone, by change, has expirience with this DAW on SDRC? Thanks, Leon

Attached is my XML config file for the Numark DJ2GO2 Touch controller.

This is a nice, small MIDI controller that is cheap and easy to find.
Enjoy!