It's all about the Software

Greetings all,

I basically reimaged my system, finally, after I can't even begin to ponder how long. So a new SSD a new install, a new experience right? All goes well, at least I thought so until I go to install my favorite SDR app. It doesn't...

i attempted to connect to an ANAN-10E which has already been verified using linHPSDR. Result: Nothing found, sorry!

however, in the logfile, there appears a response when i lied to SDRC 3.0.26 and told it to look for a Hermes Lite.

Note the...

Hello to the group,

In transmit mode, no data ( power - swr - drv - vdd) except ALC in the transmit meter display.
Screenshot-2024-08-22-111012.jpeg

Thanks for reading !

Renauld ON4KVI

Hello, I have been experiencing this bug for a while but recently noticed that I can easily recreate it just by quickly switching back and forth between receivers. Here is what happens:

1. Create two or more virtual receivers (i usually have 3...

Hello!
I am looking for help, explanation, ideas for my situation..
I'm a SDR Console user from ver 3.0.26 (2020-12-14) and now I'm @ ver 3.3 build 3236 from (2024-02-05)

Strange things started a month ago - the program did not start (the frequency...

Using SDR Console version v3.3 build 3195.
Context:
Using favourites with multiple receivers where each receiver has a different audio device.
All these audio devices are VAC's and feed different decoders.

When I add a new receiver, select its...

I have 3 ADALM Pluto sdr's all set up using IP addresses. It does not matter which one I select, it only uses the first one in the list.

Hi,

I'm developing a device to remote control the console and I observed an anomally with the MD command using the Serial port (CAT) connection.

As the documentation say (

MD
Mode
Read: MD; returns the current mode.
Write MD ;
Note: the mode...

I see we can create 8 receivers but only have FA-FF (6) commands for set/get frequency. Can we get FG and FH added?

Helllo, recently tried out the MIDI functionality which is really nice. Thanks for that. I have found that if I make a slider for volume control that has a range of 0 to 127, the software detects it properly and sets the values in the midi config...

When I try to connect to bladeRF v2 in SDR console please wait appear and then I see crush report.

crash report:

SDR Console has been working flawlessly until today when a Windows update installed. Now SDR Console will run only a minute or two then freezes, accompanied by the disconnect sound ding. I can click on the stop button, wait a minute or so, then...

So when I reboot the PC that the server is installed on, the system status comes up on-air-services unknown
To get things to work I have to stop the service in the server manager and then restart, and then everything works fine.
Now if I reboot...

zoom function with external radio doesn't work in the right way, the signal move from the tuned frequency. changing zoom an offset on the sdr tuning about 1 kHz is applied.

In addition moving radio vfo change the zoom on the spectrum.

Tracking in...

I'm observing SDRC crashing when using 8 MHz bandwidth. This has been a long running problem I've never reported because I seldom use more than 2 MHz of bandwidth and the crashing at 8 MHz of bandwidth is at random times.

Though there may be a...

Just noticed this error(?). When selecting Pre-Amp on/off a window pops up saying the AGC must be off? Pre-amp works just fine on or off with AGC on.
Just uploaded the latest, V3.3 build 3236 on a W10 laptop
See screenshot

73 Kriss KA1GJU

Hello,

I'm having an External Radio Error During program Launch with the current and last few Beta versions. I'm using a TS-590SG with SDRPlay's RSP1a SDR and OmniRig. During SDR Console program startup there is a really long delay before the the...

Hi,

SDR Console 3.3 / Pluto Plus / CN-0417 Preamp / DX Patrol 12w Amp.

When I first power up the Pluto+ and run SDR Console I can’t get any TX power out on voice or tone. The TX button in SDRC changes colour and I am showing a modulated signal or...

For me and another radio amateur friend, the sensitivity in the display dropped drastically after installing 3.3. Where previously S9+5 were at the top of the upper QO-100 beacon, I only saw S3.
We had installed the new version over the old one 3.2,...

Hi
Just got my SDR Blog V4 in the mail. Installed it and it works nicely with SDR console locally along with SDR Blog V3 (working nicely in locally and server mode). I have set up the SDR Console Server the SDR Blog V4 seems not to work correctly....

Hello all!

It looks like that the (latest 3.3 LTS) SDR-Radio.com (V3) installer does not report the application installed version to the system:

screenshot.png

Is there any way to find SDR-Radio.com version (without opening the application)...

Hi Simon,

I'm using now since a few months SDR-Console and I'm very happy with the program, I'm using the latest version 3.3 with the latest build from December last year.

I have 2 issues, one related to the hanging of the program, but I think I...

Good morning everyone!..I'm trying to use 2 instances of SDR Console connected to 2 RSP1As (and obviously to 2 different antennas) with Log4OM2 via Omnirig and related serial ports emulated via com0com

At that time....

launching the first instance...

Hello, I'm using SDR console and I'm controlling it via CAT. My receiver is an airspy hf+, connected via spy server.
When I set a new frequency via CAT, outside the currently visualised spectrum, sometimes the receiver becomes mute. As soon as I...

Nice to meet you everyone.

I was listening to FM stereo broadcast on SDR-Console v3.1 with headphones and noticed that the left and right sounds were reversed. Sounds normal on SDR# and SDR++. I thought I might have made a mistake in the settings,...