It's all about the Software

The Automatic Scheduler on the Satellite viewer is not saving changes to the min elevation .
It comes up with 0 degrees always, no matter how many times I tried to changed it.
I reverted back to the official version to confirm, and the official...

If while recording data you adjust the zoom, the resulting display doesn't correspond to the correct frequency.

Hi,

I have setup my Contour ShuttlExpress to act as a MIDI controller for SDR Console.
The outer jog wheel is setup for fast tuning (Norm, x10, x100), based on the position of the jog wheel.

Turning the jog wheel to the left sends a Control...

Hi Simon,
in this period i'm playing on VLF using up converter and RTL-SDR.
I have a difference between the frequency indicated in the bar at the bottom of the signal and the one at the top-left.
The markers are positioned referring to the...

Odd behaviour with the OEO firmware.
Everything seems to be samplet wrong. If I set 3MHz sampling it seems close to working but is too much for my pluto on ethernet.
Using the standard 750KHz I used to is giving odd signals.
This only happens with...

Hi guys, I have an issue with V3.1, often it freezes on startup. I have 2 profiles, the Main for an RTL-SDR Blog V3 and a second profile for an SdrPlay RSPDX.
At any given time I only have one oif the above SDR's connected.
The installation has...

Hi Simon,

One of my equipment configurations in my shack is running my Airspy connected to a buffered IF tap on my FT890. The FT890 upconverts to a 70.455 MHz. This gives me multiple receivers and the benefit of the waterfall.

Because I upconvert,...

I manage to connect my radio via omnirig and display follows in external radio but RX SDR does not follow the frq of my TX

Hi,

Might just be me, but in using the Radio Frequency box that comes up by pressing Home/Frequency
that allows the setting of Frequency and Span:

Again, it might be me, but it seems that the numbers you enter do not appear, always, where you have...

Hi!

Version 3.1 2365 using Windows 11 Intel 10700k NVidia 3070 has no effect when activating noise filters. This was also in the non-beta version 3.1.
Most other functions except Notch on as the filter bandwith, etc work nicely. I have used it on...

I have not been able to use the video recorder feature and the Start button is 'greyed out'. I've looked in the settings and I assume I don't have to enable it in the options. I am using the latest test version although I've not been able to use it...

Hi Simon,
Hi all,

I use v3.1 beta Build 2346 on my Dell Laptop running Win10, updated recently to functional update 21H1. Now Win10, Version 21H1 (Build 19043.1202).
After a couple of hours of operation SDR Console stops working. This was not...

program starts fine but will not connect to rsp1a,, but if I start another program first ( SDuno, or HDSDR) then go back to program it starts just fine. Does this every time.. Any idea??

Getting to know Simon's Map (latest v1.2).

When I set the option to goto Full Screen on startup - it does that.

However when it does startup it briefly shows the menus and map then expands
so that only the map appears on my Laptop screen. OS is...

Repeatable crash in v3.1 (and prior versions):

I left-click within the left half of the waterfall display to pan to lower frequencies. That works fine until the zero-Hertz spike appears and I left-click to the left of it. Then the SDR Console...

I just loaded the 2365 beta and the RSPduo won't start. It looks like it does, but nothing happens after clicking on the SDR to select it on the radio selection screen. It doesn't crash, just nothing happens.

The previous version 2346 worked fine....

Scrolling through the displayed frequency span the tuning bars disapear. Clicking on the signal tunes the radio to 10MHz WWV.

See attached screen recording.

SDR-C Ver.: 3.1 2320

73,
Hauke (VK5HW)

when I try to change frequency's it just keeps playing the same audio and the only way to change frequency's is to turn of and on the scanner. i use a rtl-sdr

Note: on my laptop it works completely fine so i know the rtl-sdr is good

Trying to run two HermesLite-2 radios at the same time in two instances of SDRC. (One is HermesLite-2 (latest built) and other one is Radioberry+RPi4)

I can run either of them individually but I cannot run them both at the same time. I can run two...

HI Simon, Folks,

I tried to install the RX-888 mkII on my PC, used the dedicated USB Drivers and installed the latest SDR-Console version.
Also followed the USB recommendations....

BUT...after selection RX-888 in the local RX menue it tries to...

Hi Simon,

After editing about 50 FAV entries in a row the FAV ADD, UPDATE and Organizer buttons don't response anymore.
The buttons EXPAND, + and - are still working.

It also takes a very long time before Markers/Config opens.
After stopping the...

v3.1 weird tune and freeze PC
I use SDRPLAY RSP2 v3 api on I7 9900k with C:2TB SSD (+3xHD) and 32GBram, CPU used 5/20% depending on the open RX and activity.

Since installing version v3.1 I have these problems:

1. when I open some receivers from...

Hey there,

either I am too blind to check it out, or it seems that the porgram shows the wrong frequency after I dialed/switched it to look around . I used the numbers on the left, also the black-yellowish slider at the lowest bottom.
I could not...

Hi Simon,

When adding/edit Favourites they are not automaticly added/changed in the FFT (as a marker).
To activate every change one have to go to View, Markers, Marker Config, uncheck Fav and check Fav again. A bit cumbersome that way.

Is it...

Hello Simon,

With V3.1, the stability of the QO-100 Beacon Synchronization seems to be noticeably lower than it has been with V3.0.28. While V3.0.28 (and before) showed a sync stability in the order of 1-2Hz, the stabilization is jumping around by...