It's all about the Software

Hello Simon.

I'm transmitting with SDR Angel / Hack RF and I'm trying to decode with RTL/SDR Dongle + SDR Television.

I'm well able to see the constellation but I have Incorrect PAT checksum and impossible to decode any images.

Do you have any...

Hello.

I'm trying to run DATV Television app on two different PC but it doesn't start.
One PC is running Windows 10 and the other has Windows 11 and the Television app was installed at the same folder (C:Radio\SDR-Radio.com (V3)) of SDR Console on...

Solved: missing driver

Hi, Simon. I believe I've found a bug in SDRC's MIDI interface. Windows only allows one application to listen to a Midi controller. Which means that apps need to take into account that a controller might already be used by another app, and if so,...

Squelch does not work on AM, I listen to the AIR band and AM/ SSB sql level does not work. Any Ideas or is there a fix for this.

Hi,
I have an external radio Elecraft K3 and a SDR radio Perseus. It works fine until I change the band or the frequency. If I change it, the spectrum and waterfall stop working. It's just noise. To fix it, I have to turn the external radio off and...

SYMPTOMS
1. When SDR Console window remains minimized, the memory usage continuously increases. It can reach insane levels of memory usage until the application can stop responding or crashes.
2. Restoring the window causes very high disk activity...

Using Windows 10/11, the WINGET utility identifies the SDR Console (V3) version as Unknown .

>winget list SDR-Radio.com (V3)
Name Id Version Available Source
----------------------------------------------------------------
SDR-Radio.com (V3)...

I just recently started playing with SDRs and I've had a hard time finding the source of this audio distortion in SDRC. I don't have this issue with SDR console. Screenshot-2025-03-17-183002.jpeg I uploaded a recording to yt so you can hear what I'm...

SDR Console version 3.4 build 3569

1，When recording data, the frequency in the file name is inconsistent with the actual frequency. I think it is correct to use the current actual received frequency as the file name. In addition, after changing the...

SDR Console version 3.3 build 3236.
I have a new Adlam Pluto just out of the box last week.
I am having problems with stopping and re-starting the Console.
On startup, Select Radio > Definitions > Search Pluto SDR
produces 3 instances. One with an...

I have not been able to get the LimeRFE to work above 100 MHz with SDRConsole. What I have found is the logic levels on U9 (SW6_V2 & SW6_V3) are not correct at 222 MHz. As such it can not receive or transmit on J3 at 222 MHz. SW6_V2 has to be a 1...

SDRC v3.3

When rapidly changing frequencies, sometimes the external radio frequency does not get updated to match the SDR frequency. It usually tracks even when scrolling rapidly, but 5-10% of the time does not. The fix is simply to change...

hello, i have a problem with sdr, namely when i connected a 3.5-52mhz longwire antenna, there appeared such dashed lines on the waterfall in sdr console v3.3, as if reflections of the broadcast station, rf gain is 29.7db
I have rtl sdr v4 Is there...

The spectrum of a spyserver shows op with a peak carrier on any entered receive frequency and a valley around it.
On certain higher frequencies the whole display starts bouncing up and down.

When using the SDR# client all is fine.

You can try with...

Hello! the first audio is with SDR# , 2 meter band, ham qso, NMF 12 khz...the second is with SDR console without noise reduction, NFM 12 knz...device RTL SDR v3, gain set to 38 for both, same time, same antenna, same PC...where am I going wrong?

Hi. I had installed the 3.4Beta version of the console on my own computer and my intention was to use it as a PAN adapter together with a Yaesu FTdx5000 radio. My SDR receiver is a FunCube pro+. The signal is controlled from the IF connector of the...

Hi Guys, I am new here and to the SDR hobby but, I am a long time Radio Ham, G0EMJ.

The problem is that I have 2 SDR units, RTL-SDR and Nooelec NESDR SMART but, neither one of them will pick up a station on 105.4 mhz FM.
This is a station I listen...

I have Omni-Rig v2.0 installed and running and am able to connect to SDRUno just fine and control my radio (FT-991A). I have installed SDR Console (v3.3) and even the Beta (3.4) and am unable to connect to my external radio because it constantly...

Hello all....

I was on QO100 calling CQ whit my voice keyer running, after som call a other ham told me that I was to wide, arround 3.5khz++

I have my settings on 3Khz BW in sdr-console 3.3, so I am a littel confused about that I have so big BW...

I have a problem, SDR Console freezes, mostly when I use the satellite function.
You can still hear the sound, but the interface freezes completely and there is no error message.
I have to close the program using the task manager.
I have already...

Hi,

I'm developing a device to remote control the console and I observed an anomally with the MD command using the Serial port (CAT) connection.

As the documentation say (

MD
Mode
Read: MD; returns the current mode.
Write MD ;
Note: the mode...

I have a user that probably doesn't know that one can use the pre-amp even with the AGC on.
It might be too late to train this person that you don't have to turn off the AGC to get a preamp on
for use when on 20m and higher.

I am forever finding...

Hi, new on this forum.
I use HL2 with all softwares like Thetis Sparksdr and Quisk, but with SDR console V3.2 or 3.3 the output power is around 0.5 W when speaking in the mic ( drive , proc & gain 100%) - Tune or whistle gives around 4 W a little...

Greetings all,

I basically reimaged my system, finally, after I can't even begin to ponder how long. So a new SSD a new install, a new experience right? All goes well, at least I thought so until I go to install my favorite SDR app. It doesn't...