It's all about the Software

SDR Console has been working flawlessly until today when a Windows update installed. Now SDR Console will run only a minute or two then freezes, accompanied by the disconnect sound ding. I can click on the stop button, wait a minute or so, then...

So when I reboot the PC that the server is installed on, the system status comes up on-air-services unknown
To get things to work I have to stop the service in the server manager and then restart, and then everything works fine.
Now if I reboot...

zoom function with external radio doesn't work in the right way, the signal move from the tuned frequency. changing zoom an offset on the sdr tuning about 1 kHz is applied.

In addition moving radio vfo change the zoom on the spectrum.

Tracking in...

I'm observing SDRC crashing when using 8 MHz bandwidth. This has been a long running problem I've never reported because I seldom use more than 2 MHz of bandwidth and the crashing at 8 MHz of bandwidth is at random times.

Though there may be a...

Just noticed this error(?). When selecting Pre-Amp on/off a window pops up saying the AGC must be off? Pre-amp works just fine on or off with AGC on.
Just uploaded the latest, V3.3 build 3236 on a W10 laptop
See screenshot

73 Kriss KA1GJU

Hello,

I'm having an External Radio Error During program Launch with the current and last few Beta versions. I'm using a TS-590SG with SDRPlay's RSP1a SDR and OmniRig. During SDR Console program startup there is a really long delay before the the...

Hi,

SDR Console 3.3 / Pluto Plus / CN-0417 Preamp / DX Patrol 12w Amp.

When I first power up the Pluto+ and run SDR Console I can’t get any TX power out on voice or tone. The TX button in SDRC changes colour and I am showing a modulated signal or...

For me and another radio amateur friend, the sensitivity in the display dropped drastically after installing 3.3. Where previously S9+5 were at the top of the upper QO-100 beacon, I only saw S3.
We had installed the new version over the old one 3.2,...

Hi
Just got my SDR Blog V4 in the mail. Installed it and it works nicely with SDR console locally along with SDR Blog V3 (working nicely in locally and server mode). I have set up the SDR Console Server the SDR Blog V4 seems not to work correctly....

Hello all!

It looks like that the (latest 3.3 LTS) SDR-Radio.com (V3) installer does not report the application installed version to the system:

screenshot.png

Is there any way to find SDR-Radio.com version (without opening the application)...

Hi Simon,

I'm using now since a few months SDR-Console and I'm very happy with the program, I'm using the latest version 3.3 with the latest build from December last year.

I have 2 issues, one related to the hanging of the program, but I think I...

Good morning everyone!..I'm trying to use 2 instances of SDR Console connected to 2 RSP1As (and obviously to 2 different antennas) with Log4OM2 via Omnirig and related serial ports emulated via com0com

At that time....

launching the first instance...

Hello, I'm using SDR console and I'm controlling it via CAT. My receiver is an airspy hf+, connected via spy server.
When I set a new frequency via CAT, outside the currently visualised spectrum, sometimes the receiver becomes mute. As soon as I...

Nice to meet you everyone.

I was listening to FM stereo broadcast on SDR-Console v3.1 with headphones and noticed that the left and right sounds were reversed. Sounds normal on SDR# and SDR++. I thought I might have made a mistake in the settings,...

Hi
This issues just started today. Start SDR Console 3.3 3195 (using Ham Radio Deluxe, VSP Mgr, Omni Rig, Yaesu 1200, SDRplay RSPdx) and it will randomly lock up. No movement on waterfall, can't change the radio freq via SDR Console, clicking the...

Hi Simon,
there are some waterfall differences between sdrconsole 3.2 and 3.3 version, viewing the same signal, using an RTL-SDR V3 dongle on USB, at 250 & 300 kHz bandwidth.
Some screen shots, with the same configurations

73 Rocco IK8XLD

Hi, new on this forum.
I use HL2 with all softwares like Thetis Sparksdr and Quisk, but with SDR console V3.2 or 3.3 the output power is around 0.5 W when speaking in the mic ( drive , proc & gain 100%) - Tune or whistle gives around 4 W a little...

HI,

I'm using Version 3.3, Build 3195 on Windows 11 and noticed the following reproducible two bugs:
After pressing the E2 button (Filter Low) on the ELAD TM-2 controller, the programm crashes (a message pop's up: please wait - but nothing happens)...

SDRC v3.3

When rapidly changing frequencies, sometimes the external radio frequency does not get updated to match the SDR frequency. It usually tracks even when scrolling rapidly, but 5-10% of the time does not. The fix is simply to change...

I have a Hermes-lite 2. If I activate the option Band voltage for the Hermes-lite 2 I ever get the same output voltage from the HL2, independ which frequency I select - no changes.
With other software (in this case Thetis) all is working correct,...

Hi,
so I went the cheap way, because this is what I could afford. I bought a clone RSP1A from Aliexpress.
It works fine with SDRConnect.
Does not start with SDRUno no matter which version, albeit it starts right after installation, but not if I...

External radio IF offset for different modes works at startup. But if the mode is changed while SDRconsole is running, the new offset is not updated/applied.
For example, if started in USB (SSB-U), the SSB-U offset is persistent for the entire...

Hello! I was having an issue with the cuda fft support where it seemed like the cuda driver would fail and the cpu driver would take over. This was noticeable because the waterfall noise floor would move faster in cpu mode, and the noise floor...

Hi All, I apologise if I don't provide too much info. Equipment: Pluto. I had SDR Console 3.2 + Virtual cable working with FT8, once installed 3.3 it stopped working. The WSJT was unable to activate TX correctly. If I increased audio level coming...

I've been having trouble with the mute either not working at all, or recovering too soon. I use SDR Console with a lower power boat anchor. It worked fine for hours and now won't mute the strong signal from my transmitter which is bleeding through...