It's all about the Software

When using the Receiver Noise Reduction NR3 my Transmit Audio is distorted. When I change to NR1 all is OK. I didn't think there should be a correlation between the receiver settings and the Transmitter functions.
73, Don

Hello,

Sorry, but I realize that I just posted this in the wrong Forum, and that it should be here, probably.

In the select radio screen, it will not accept the Airpy HF+ Discovery, even though it shows as a choice, and I have the Definitions,...

I'm not sure if this has been reported already and if it is a bug or such kind of oddity.
So far I've seen it on the R2, the RSPDX which I use remotely doesn't show this behavior.
The frequency of the radio (the real frequency, not what is shown by...

Normally the frequency change either via the numerical or the spectrum display is instantaneous and without any delays, but now for the second time in a couple of months this is not the case.
Jumped over to my Linux drive and tested the radio's with...

I was running v3.0.26 before, installed the March 26 v3.0.27 and the RDS clock time or CT is showing an hour ahead on all stations that send it.

My region uses RDBS, 75us, and these are strong local signals with the thumbs up icon, bit correction...

I have noticed a minor issue in the Memory tab, that I don't know if it is actually a bug or if the program works kike that by design.
Since I had to do a clean installation, I exported the Memories and View Markers to XML and CSV.
Then I did the...

Immagine 2021-03-26 051423.png
Hello, I found in 3.0.27 that the digital decoder does not work, as soon as it is activated it goes into waiting status and crash the program!
The rx in use is AIRSPY HF+ DISCOVERY
Thanks for your help
IU4FIR Massimo

Just installed the new release. The problem I have is Shaded will not stay enabled in the spectrum, after restart.
The odd thing is that when running on my laptop as a remote setup, this problem does not happen.

Philip G7JUR

installed latest version from 26th of march
the psk clock in the beacon window does not turn anymore

Installed version 3.0.27 on my VAIO laptop running Windows 10 64-bit and GPU is NVIDIA GT 540M
After installation, FFT on HF stopped working. After a couple of minutes the GPU crashed and Windows disabled the GPU.

Note: I had no issues like that...

SDR Console v3.0.27

IF Display On/Off toggle button does not work.

de JH5GON

The visual gain control behaves peculiarly. If the visual gain is set too high the radio overloads. If it is set too low the signal vanishes. The visual gains at which it misbehaves depend on the RF gain setting. This appears to be seen with several...

I receive an error after taking a screenshot when I select Open or Open with... . A message popup indicates: Windows cannot find 'C:\Users\PC\Pictures\SDR-RADIO.com (V3)\Screenshot-2021-02-09-001234.jpeg' Make sure you typed the name correctly, and...

Part of the Screen message:
SDR Console.exe caused ACCESS_VIOLATION in module C:\Program Files\SDR-Radio.com (V3)\libiio.dll at 0033:0000000063FE5AE5, iio_buffer_first()+21 byte(s)
This bug appears after about 1 minute, I had started the SDR...

In SDRPlay RSP1::SDR Console v3.0.26

In the Rec/Playback tab
clicking on the Record button in the Data:Record section brings up a Start Recording window.
It appears to be extending beyond the bottom of the screen. Screen shot attached.
Its start...

Hello Simon,

Further to my previous post about the Pluto uncommanded transmit bug when starting or changing bandwidth in Console.

As I noted, I first noticed a similar problem had newly occurred using Satsagen, the spectrum analyzer program for...

Hello,

problem:
Initial correction of SDR calibration not applied to Software at startup!
Using Correction factor of 2.044 ppm.

Visualization:
QO-100 Middle normally at 10489.750 but at startup (without any interaction) is active on 10489.729x...

Hello Simon,

I installed the latest version of Satsagen, the spectrum analyzer software for my Pluto and found that when adjusting the span setting that the Pluto would go into transmit for a moment with every change of the span setting.

I queried...

First, this amazing software combined with my Airspy HF+ have returned me to listening.

Being lazy I often record large portions of the AM band to play back and extract IDs. The time shown on the playback doesn't match real time.

If it was just my...

i attempted to connect to an ANAN-10E which has already been verified using linHPSDR. Result: Nothing found, sorry!

however, in the logfile, there appears a response when i lied to SDRC 3.0.26 and told it to look for a Hermes Lite.

Note the...

Since I did that 3.0.26 update my receiver won't remain stable and drifts all over the place (see attached).

Hi Simon,

Please see the attached picture and the two red arrows.

If I open a menu item that pops up a new window like VIEW - MORE OPTIONS - SELECT then close it, an inner border results after closing. The border is not the border of the pop up...

This is from KB7IJ who is trying to run SDRC with WSJTX on an Icom 7300.
Please help if you can, we are at wits end. Bottom line:
The combinations works with a Kenwood TS-2000, but it throws the SDRC error when used with an Icom 7300
Thanks much...

Hi Simon

Running Scheduled Recording with v3.0.27 build 2124 of January 19, 11:02 the radio (AFEDRI) is stopped at the end of recording even that the new box (Stop when finished) is not checked.
This is not desirable.
The radio is stopped at the...

Using low-performance laptop with Win7, data file recorded from Elad FDM-S2.

Haven't yet been able to spend much time exploring this program, which seems to have super potential but gets hardly a mention here. Can someone please explain an apparent...