It's all about the Software

Hi, Simon.

Thank you for the reply to my report in the groups.io list.

I asked the question because I saw something beneath the AM Squelch item in the Squelch panel. Whatever it is, it lights up when you mouse over it, which led me to think that...

Not sure if what I am observing is a bug, behavior by design, or something I am missing.

A key point before I go on is that I am a laptop user without an external mouse or scroll wheel. I just have the laptop touch pad with left and right mouse...

I'm sure I'm missing a setting (I think)

When I set the display to show UTC Time, the Schedule shows local time

Is there a setting to make the Schedule also show UTC time?

Thanks.

Clicking on the top of any Console window brings up the two way arrow but instead of resizing it moves the window, the same procedure on the left, right and bottom edges behave as expected resizing the window. Not a show stopper but I seem to always...

Hello,
After updating my 2 pcs to W10 21H2 build 19044.1566 and W11 21H2 build 22000.527 both SDR-Console 3.1 and also 3.0.27 no longer run. I get various problem like frozen screen upon starting, sometimes audio but no spectrum, can´t select radio,...

I´m new to this forum because it´s the first time I have problems. I can´t really figure out how it started but this is how it is now:
I´m using Win 11 21H2 build 22000.675
and two times RSP1A. First the RSP1A´s couldn´t started. Seems I had some...

Hardware:-
Hermes Lite 2 with firmware 72.8
Software:-
Windows 7 Home 32 bit
SDR Console compiled on 2022-04-12
Symptom:-
Maybe after one or two transmissions, on going to transmit, Hermes Lite relays chatter continuously, no transmit output. On...

Bug? The long path seem to be anchored on the opposite side of the earth from the home location.

Nice to meet you everyone.

I was listening to FM stereo broadcast on SDR-Console v3.1 with headphones and noticed that the left and right sounds were reversed. Sounds normal on SDR# and SDR++. I thought I might have made a mistake in the settings,...

zoom function with external radio doesn't work in the right way, the signal move from the tuned frequency. changing zoom an offset on the sdr tuning about 1 kHz is applied.

In addition moving radio vfo change the zoom on the spectrum.

Tracking in...

Test setup, RX888 at 30m with a narrowband 500Khz bandpass filter inline, also without the filter the problem is present.

This is the spectrum on wspr waterfall, when using the bw setting of 2, 4 and 8 there is some inter modulation from what it...

Hardware: Hermes Lite 2 with Windows 7 32 bit computer
Software: SDR Console version 3.1 build 2320
Issue: Both sides of a conversation only get recorded if in the *** Options -> Hermes Lite window -> Tx Options -> Mute Rx check box is left...

Software: SDR console ver 3.1 build 2320
Hardware: Hermes-Lite 2, 32 bit Windows 7 computer
Problem: After keying the voice keyer and then cancelling it, the scroll wheel no longer fine tunes the radio frequency. However, left mouse will step change...

I used SDRConsole to snip a 10 second portion of an I-Q file recorded by SpectraVue.

However, the snipped file does not playback in SpectraVue - an error window pops up Input file not valid . The new snipped file does playback in SDRConsole.

Whit

I'm a huge SDR-Console fan. I BCBDX which means listening around the top of the hour. Over time the clock on my recording doesn't track the real recorded time but drifts behind. I have a ten hour recording and it's almost a minute behind after that...

First, I love the SDR COnsole interface for my R-8600. I have noticed that the Noise Blanker (enabled) and NR filters (NR1 thru NR4) have no effect on R-8600 received signals.

Hi Forum,

i've noticed some weird behaviour with Receive or Transmit Pane undocked.

1. Frequency or Mode doesn't change when TX Pane is undocked:
Sync RX on Frequency and Sync RX on Mode are both activated.
Frequency doesn't change neither with...

Hello and a happy new year!

I am using the following setup:

Hermes Lite 2
Hardrock-50 amplifier
serial cable connection between TRX and PA

Until SDR Console V3.1, 64-bit, 2021-11-22_0623 automatic band switching of the Hardrock-50 worked...

SDRC v3.1 3AUG2021
WIN10

Greetings

Bug(s) :

1) 'Memories' entries set to BC-FM revert to Narrow FM after ~1 seconds after selection, a 2nd click sticks to BC-FM
2) filter width on display not reflecting BC-FM selection
3) BC-FM entry on Main...

Hi,
I'm using a funcube dongle pro+ I've bought a new desktop recently, I didn't have any problem
running SDR Consul but since the new PC the programme keeps locking up every miute?

I've checked up all updates but it keeps doing this?
Has anyone an...

SDR-Console has a weird bug with any AIRSPY HF+ (Discovery or dual port) that doesn't happen with SDR#.
I can't receive anything within a few MHz of 20MHz unless I reduce the sample rate to 384kHz.
At 768kHz when tuning within 2 or 3 MHz of 20MHz...

when qsy in the tx box the tx frequency changes in that same moment i do it (like it should be)

when i change the frequency by midi or inside the rx panel the tx does not follow (at the same moment) but just after tx-ing once

version 2511 10th of...

Hi, I have encountered a problem using HERCULES DJ CONTROL STARLIGHT as a MIDI controller. ( DJ Control
The volume control is not linear but works in jerks, going from level 0 to 65 or 100 with a few mm of rotation on the command, it also happens...

To use a bandwidth of 50 MHz, the following device string is needed:

peak=0.003906,otw_format=sc8,addr=192.168.10.2,uhd

works great with gqrx at the same system,

but sdr-console crashes, also the newest version.

if crash dump or any other...

Hi Simon et al

I have got back to SDR Console after a long break, and I am trying to use it on a small mini-PC running W10. It uses a T2250 1.73GHz CPU with 2GB of RAM.
SDR Console 3.1 build 2320. AirSpy or FunCube Dongle, both receive OK, but if I...