It's all about the Software

SDRC v3.1 3AUG2021
WIN10

Greetings

Bug(s) :

1) 'Memories' entries set to BC-FM revert to Narrow FM after ~1 seconds after selection, a 2nd click sticks to BC-FM
2) filter width on display not reflecting BC-FM selection
3) BC-FM entry on Main...

Hi,
I'm using a funcube dongle pro+ I've bought a new desktop recently, I didn't have any problem
running SDR Consul but since the new PC the programme keeps locking up every miute?

I've checked up all updates but it keeps doing this?
Has anyone an...

SDR-Console has a weird bug with any AIRSPY HF+ (Discovery or dual port) that doesn't happen with SDR#.
I can't receive anything within a few MHz of 20MHz unless I reduce the sample rate to 384kHz.
At 768kHz when tuning within 2 or 3 MHz of 20MHz...

when qsy in the tx box the tx frequency changes in that same moment i do it (like it should be)

when i change the frequency by midi or inside the rx panel the tx does not follow (at the same moment) but just after tx-ing once

version 2511 10th of...

Hi, I have encountered a problem using HERCULES DJ CONTROL STARLIGHT as a MIDI controller. ( DJ Control
The volume control is not linear but works in jerks, going from level 0 to 65 or 100 with a few mm of rotation on the command, it also happens...

To use a bandwidth of 50 MHz, the following device string is needed:

peak=0.003906,otw_format=sc8,addr=192.168.10.2,uhd

works great with gqrx at the same system,

but sdr-console crashes, also the newest version.

if crash dump or any other...

Hi Simon et al

I have got back to SDR Console after a long break, and I am trying to use it on a small mini-PC running W10. It uses a T2250 1.73GHz CPU with 2GB of RAM.
SDR Console 3.1 build 2320. AirSpy or FunCube Dongle, both receive OK, but if I...

For radio operation on 2.4GHz via the QO-100 satellite I use the Adalm-Pluto Rev-B and Rev-C (brand new) + PA and on the narrow band SDR Console 3.x for control. Some of my radio friends have found through measurements with high-quality spectrum...

When I start the program (v 3.1) I get a message:

this action cannot be completed because the other program is busy
I am using a Yaesu FTDX5000 , omni rig, the Yaesu SCU-17 and an SDR Play. Sometimes after hitting the switch to button several times...

The gain of the receiver id down about 5 db from build 2431 so went back to build 2431.

Greetings

Simon Brown has been graciously trying to help me locate the cause of this crashing problem :

Configuration-A was experiencing occasional crashes, but also occasional smooth operation. Simon instructed that this configuration was not...

Greetings All,

Having a couple SDRC show-stoppers today and noticed there was a WIN10 Update installed today, anyone else having problems ?

Problems :

1. Cannot Search for radios to add in Definitions . Before the crash, was operating HF+, after...

Simon brown!

A long time ago I owned a perseus and discovered changing the visual gain would also effect the DSP.
We fixed that bug.

Now, in an effort to reduce noise, I bought a mac mini 7,1 and put windows and SDR-Console on it.
I set it up as...

When I am recording a data file, pressing Stop and then Open (to delete or review the recorded data file) in quick succession results in a computer crash. It locks up, comes up with a message Out of memory and then the PC completely freezes...

please wait overlay + audio disconnect, however interface continues to run in background.
To trigger: start sdr-console on desktop, then open RD client(by microsoft) on iphone, ipad, or other device.
SDR-console will continue working. Then, go back...

Here's a weird one.

I need to dig deeper with this and see if I can reproduce it, however, bear with me...

CQWW SSB. Recorded 40m SSB, and 20m SSB for the entire length of the contest, both on the same machine, both using separate Elad S2s.
20m...

G'Day,

I've just noted that there seems to be an issue when running multible receivers.
Say I have three RX's, 10/15/17, and audio going to three different cables (virtual). I can get only two outputs to work. Strange think is if I make the last RX...

The problem occurs in 3.1 Betas from September and November, using LimeSDR

After tx-calibration the calibration-values are shown correctly in the adv. options page, but the DC-Q-value is stored incorrectly. after reload it is reset to 0, which...

Hi Simon
LimeSDR USB ,Win 10 64b.
In version 2431 Nov 22 (and maybe is some recent 'test team beta' versions), the DRIVE slider on the transmit pane does not change the power when doing a 'TUNE'.

It does work in 'TONE' and in normal TX.

TIA de Joe...

I'm trying to get SRD-Radio running with an RSPduo. The installation mostly went OK, with the exception of the following problems:

(1) SDR-Radio V3.1, 64bit, 2021-08-03_1111 wants SDRPlay 3.06 API and not the current version 3.08

19:09:52.298:...

Hi,
I have an Elecraft K3, Omnirig, Perseus and Windows7 with SDR Console v3.1. When I change a band on the K3, an External Radio and SDR radio on console is switched to VFO B on K3, but K3 is still working on VFO A. And I have VFO A correctly set...

Does not display symmetrically in AM mode, but does properly in all other modes.

The Automatic Scheduler on the Satellite viewer is not saving changes to the min elevation .
It comes up with 0 degrees always, no matter how many times I tried to changed it.
I reverted back to the official version to confirm, and the official...

If while recording data you adjust the zoom, the resulting display doesn't correspond to the correct frequency.

Hi,

I have setup my Contour ShuttlExpress to act as a MIDI controller for SDR Console.
The outer jog wheel is setup for fast tuning (Norm, x10, x100), based on the position of the jog wheel.

Turning the jog wheel to the left sends a Control...