It's all about the Software

I’m working on C# code that sends commands to SDR-Console. One of my tasks is to identify the current Mode in SDR-Console. If I select “BC-FM” in Console and send the “MD;” CAT command from my software, I expect to get “MD9;” in return as documented...

New user, have SDRPlay connected to Rcv Out on my IC-7600, nothing connected to Recv In, so using Console for spectrum and audio. I got it working yesterday, but now it won't connect or play anything from SDRPlay. Long story, after I had Console...

I am doing a new post on this because it seems to be a separate issue from the Favorites issue I posted earlier though the Favorites issue is being impacted by this issue.

If you close the DSP Panel in a docked state and then close SDR Console, the...

Not sure if this has been spotted before - on each memory bank if you edit the 3rd memory button there is an extra option labelled Apply . It doesn't do anything though.

Same on 2 pc's. No big deal as it's benign ;)
Capture.JPG

73 John

Hi,

I notice a bug with RFspace SDR-IQ, it was tested with 2 different SDR-IQ, same result.
There is always a strong carrier on the center of spectrum:
I attached 2 screenshot where i swap the center FRQ between 1.850 and 1.875.

73
Pat
ON4AMI /...

Hi Simon,

When opening multiple sequential files that were recorded in SDRuno and editing them with the Datafile Editor, the final edited file is jumping unexpectedly when playing the edited wav file back in SDR Console v3.2. I suspect it could be...

Running a IC7300 with an internal PTRX-7300 panadapter connected to an RSP1A SDR.

I have two RSP1A's and at SDR Console startup I select whichever I want to use. 99% of the time it's the RSP1A connected to the panadapter inside the 7300.

On...

Hi I am using an RSP1A and a Yaesu FTDX-5000 on start up I can see the radio is is tracking with the vfo and the digital display. I can select the radio the RSP1A and click start. However the Start button on the upper left does not start the...

SDR-Concole v3.2
Windows 10 22H2 build 19045.2251
Windows Feature Experience Pack 120.2212.4180.0
Hardware: AMD FX(tm)-8350 Eight-Core Processor 4.01 GHz
Graphics Card: NVIDIA GeForce GTX 750Ti - Driver version 526.98 released 20221116 (this was...

Just wondering where do I send a crash report?

I have attached the report here anyway. Never mind it's too large.

To recreate the bug for RSP1A users (and possibly other radios where there is a latency setting option), do the following:

1. Start SDR Console and change bandwidth to anywhere between 6 MHz and 10 MHz.
2. Change latency to “Highest” (in Radio...

Hello,
I may be making a mistake.
The filter bandwidth is displayed at odd setting for example 2,5khz with 2,488 Hz.at even setting for example 5khz is also displayed 5 khz. Is this a bug or am I making a mistake in the settings?
vy 73 George Hz.jpg

Hi Simon. Using Win 11 and Console 3.2 on an i5-10 machine with Nvidia GTX 1650 super.
Trying to use my Pluto for Tx/Rx through QO-100.
Radio definitions - highlight Pluto - tick Converter selection and press edit.
In Converter definition page -...

I upgraded from 32 bit Windows 7 to 64 bit Windows 10 in the summer. I can still boot up either. My hardware is:-
I7 desktop with old GeForce GT 450 dual monitor gpu. Hermes Lite 2 driving an XPA125B 100W linear. My recording tests today off Hack...

I am not sure: is it a bug or not?:

I use SDRConsole for receiving QO100 (10GHZ with LNB)
It worked quite well with downconverter and beacon sync with pluto on Win11.
Then I installed the express transmitter for transmitting video using the same...

Hello,

50 Mhz Bandwidth with the USRP n210 is not working,
DebugView shows, that sc16 is used, but that bandwidth is working only with sc8.

Do you plan to fix that in the future?

Hi,

When using the datafile editor to create a new file with differend frequency and bandwidth compared to the input recording, the resulting output file is fine until the input recording file switches to a new block.
After the switch to another...

Hi,
SDRConsole 3.1 build 2575

I did run the analiser on a large recording from the 70 cm satellite band (18 hours recording) all works very nice and smooth. played back some signals from the analiser view with the play function and decoded some CW...

Installation: Win 10 Pro Dell XPS 15 Laptop, plenty of space. SDR Console installed, no attached radios.

Completed installation and didn't have a locally attached device to test with. Brought up SDRSharp, found an open Spyserver site and copied the...

Hi, version 1.25 of World Map is the last working one on my Win10 64bit notebook.
Installing 1.3 is no problem, only it won't start... 73, Alex DH2ID

Hello,

Firstly I would really like to express my gratitude for offering this software. I am really fond of it after moving over from another very common program....
I do miss some of the plugins from the other software sometimes, but not immensely...

I have been using SDR Console with my discovery HF dongle without fault for a good few years. But since changing my GPU from a GTX Titan to a Nvidia GTX 1080Ti a few months ago, there is a constant flashing of windows within the sdr console as i...

Not sure if what I am observing is a bug, behavior by design, or something I am missing.

A key point before I go on is that I am a laptop user without an external mouse or scroll wheel. I just have the laptop touch pad with left and right mouse...

Sometimes I use the analyser to look for MS pings on FM. I have noticed that there is a time mismatch between the time is listed in the analyser and what the time is in the IQ recording.

For example today I had a ping at 11:45:00 according to the...

Long term issue...I scan with the FM frequency changing every 5 seconds. When I am on a frequency (say 94.7) and no RDS is detected on the next frequency (94.9), the RDS from 94.7 is matched up with 94.9. How do I get it to start from scratch each...