It's all about the Software

Hi Guys, I am new here and to the SDR hobby but, I am a long time Radio Ham, G0EMJ.

The problem is that I have 2 SDR units, RTL-SDR and Nooelec NESDR SMART but, neither one of them will pick up a station on 105.4 mhz FM.
This is a station I listen...

Hello! the first audio is with SDR# , 2 meter band, ham qso, NMF 12 khz...the second is with SDR console without noise reduction, NFM 12 knz...device RTL SDR v3, gain set to 38 for both, same time, same antenna, same PC...where am I going wrong?

I have Omni-Rig v2.0 installed and running and am able to connect to SDRUno just fine and control my radio (FT-991A). I have installed SDR Console (v3.3) and even the Beta (3.4) and am unable to connect to my external radio because it constantly...

Hello all....

I was on QO100 calling CQ whit my voice keyer running, after som call a other ham told me that I was to wide, arround 3.5khz++

I have my settings on 3Khz BW in sdr-console 3.3, so I am a littel confused about that I have so big BW...

Hi,
i cannot use my LNB which has big drifts during daylight (over 100KHz) because the geostationary window span frequency is too small. I cannot zoom out and select the beacon to start correct tracking.

It would be nice to be possible to zoom out...

I have a problem, SDR Console freezes, mostly when I use the satellite function.
You can still hear the sound, but the interface freezes completely and there is no error message.
I have to close the program using the task manager.
I have already...

Hi,

I'm developing a device to remote control the console and I observed an anomally with the MD command using the Serial port (CAT) connection.

As the documentation say (

MD
Mode
Read: MD; returns the current mode.
Write MD ;
Note: the mode...

I have a user that probably doesn't know that one can use the pre-amp even with the AGC on.
It might be too late to train this person that you don't have to turn off the AGC to get a preamp on
for use when on 20m and higher.

I am forever finding...

Hi, new on this forum.
I use HL2 with all softwares like Thetis Sparksdr and Quisk, but with SDR console V3.2 or 3.3 the output power is around 0.5 W when speaking in the mic ( drive , proc & gain 100%) - Tune or whistle gives around 4 W a little...

Greetings all,

I basically reimaged my system, finally, after I can't even begin to ponder how long. So a new SSD a new install, a new experience right? All goes well, at least I thought so until I go to install my favorite SDR app. It doesn't...

i attempted to connect to an ANAN-10E which has already been verified using linHPSDR. Result: Nothing found, sorry!

however, in the logfile, there appears a response when i lied to SDRC 3.0.26 and told it to look for a Hermes Lite.

Note the...

Hello to the group,

In transmit mode, no data ( power - swr - drv - vdd) except ALC in the transmit meter display.
Screenshot-2024-08-22-111012.jpeg

Thanks for reading !

Renauld ON4KVI

Hello, I have been experiencing this bug for a while but recently noticed that I can easily recreate it just by quickly switching back and forth between receivers. Here is what happens:

1. Create two or more virtual receivers (i usually have 3...

Hello!
I am looking for help, explanation, ideas for my situation..
I'm a SDR Console user from ver 3.0.26 (2020-12-14) and now I'm @ ver 3.3 build 3236 from (2024-02-05)

Strange things started a month ago - the program did not start (the frequency...

Using SDR Console version v3.3 build 3195.
Context:
Using favourites with multiple receivers where each receiver has a different audio device.
All these audio devices are VAC's and feed different decoders.

When I add a new receiver, select its...

I have 3 ADALM Pluto sdr's all set up using IP addresses. It does not matter which one I select, it only uses the first one in the list.

I see we can create 8 receivers but only have FA-FF (6) commands for set/get frequency. Can we get FG and FH added?

Helllo, recently tried out the MIDI functionality which is really nice. Thanks for that. I have found that if I make a slider for volume control that has a range of 0 to 127, the software detects it properly and sets the values in the midi config...

When I try to connect to bladeRF v2 in SDR console please wait appear and then I see crush report.

crash report:

SDR Console has been working flawlessly until today when a Windows update installed. Now SDR Console will run only a minute or two then freezes, accompanied by the disconnect sound ding. I can click on the stop button, wait a minute or so, then...

So when I reboot the PC that the server is installed on, the system status comes up on-air-services unknown
To get things to work I have to stop the service in the server manager and then restart, and then everything works fine.
Now if I reboot...

zoom function with external radio doesn't work in the right way, the signal move from the tuned frequency. changing zoom an offset on the sdr tuning about 1 kHz is applied.

In addition moving radio vfo change the zoom on the spectrum.

Tracking in...

I'm observing SDRC crashing when using 8 MHz bandwidth. This has been a long running problem I've never reported because I seldom use more than 2 MHz of bandwidth and the crashing at 8 MHz of bandwidth is at random times.

Though there may be a...

Just noticed this error(?). When selecting Pre-Amp on/off a window pops up saying the AGC must be off? Pre-amp works just fine on or off with AGC on.
Just uploaded the latest, V3.3 build 3236 on a W10 laptop
See screenshot

73 Kriss KA1GJU

Hello,

I'm having an External Radio Error During program Launch with the current and last few Beta versions. I'm using a TS-590SG with SDRPlay's RSP1a SDR and OmniRig. During SDR Console program startup there is a really long delay before the the...