It's all about the Software

Hi

My SDR console has suddenly stopped working with my RTL SDR dongle.

It starts up and I select the dongle, but nothing shows up on the waterfall and no sound comes out the speakers.

And when I close SDR Console it crashes.

My RSP1a works fine...

Data Analyser works perfectly on the 1st analysis of each session. But moving on to a new project results in an image which appears “noisy” and overlaid with hash. In order to get a clear image it’s necessary to close the Analyser window and re-open...

Hi,

this is a crosspost, it first appeared here (I just joined the forum this morning):

I have found an entry in today's Windows Event Viewer that the SDRServerService.exe has crashed last night.

At that time, I didn't use it, and to be more...

Ignore

Hi,
When editing a 46 Gb I/Q file (see I-Q file_editing-#1 ) to extract a 200 kHz wide full lenght portion, the size of resulting file is less than 100Mb and the file covers a few minutes only of the original file (see I-Q file_editing-#2 ).
Did I...

Hello,
after update from 3.0.26 to 3.0.27 I always get an error dialogue at startup of SDR Console.
Manual press of Start button in the home menu, starts the device.
Version 3.0.26 could start directly one of my 2 two devices connected per USB.
Both...

I tried to schedule a recording.
I entered all the information, frequency, time, duration, audio format, etc.. But the OK button did not enable. So the schedule could not be saved.

Can you confirm that?

Thanks

Hi Simon,

If I take a screenshot with the Console (.27 3/24/21) on the second monitor it takes a screenshot of my main monitor. It never did that before.

Barry
WB2ZXJ

I recorded a .wav snippet from a playback of a larger recording while in Binaural SAM mode. When I listened to it, it played back in a slow manner. Not delayed, but like the recording was playing in half-speed so the voice came out real deep and...

When using the Receiver Noise Reduction NR3 my Transmit Audio is distorted. When I change to NR1 all is OK. I didn't think there should be a correlation between the receiver settings and the Transmitter functions.
73, Don

Hello,

Sorry, but I realize that I just posted this in the wrong Forum, and that it should be here, probably.

In the select radio screen, it will not accept the Airpy HF+ Discovery, even though it shows as a choice, and I have the Definitions,...

I'm not sure if this has been reported already and if it is a bug or such kind of oddity.
So far I've seen it on the R2, the RSPDX which I use remotely doesn't show this behavior.
The frequency of the radio (the real frequency, not what is shown by...

Normally the frequency change either via the numerical or the spectrum display is instantaneous and without any delays, but now for the second time in a couple of months this is not the case.
Jumped over to my Linux drive and tested the radio's with...

I was running v3.0.26 before, installed the March 26 v3.0.27 and the RDS clock time or CT is showing an hour ahead on all stations that send it.

My region uses RDBS, 75us, and these are strong local signals with the thumbs up icon, bit correction...

I have noticed a minor issue in the Memory tab, that I don't know if it is actually a bug or if the program works kike that by design.
Since I had to do a clean installation, I exported the Memories and View Markers to XML and CSV.
Then I did the...

Immagine 2021-03-26 051423.png
Hello, I found in 3.0.27 that the digital decoder does not work, as soon as it is activated it goes into waiting status and crash the program!
The rx in use is AIRSPY HF+ DISCOVERY
Thanks for your help
IU4FIR Massimo

Just installed the new release. The problem I have is Shaded will not stay enabled in the spectrum, after restart.
The odd thing is that when running on my laptop as a remote setup, this problem does not happen.

Philip G7JUR

installed latest version from 26th of march
the psk clock in the beacon window does not turn anymore

Installed version 3.0.27 on my VAIO laptop running Windows 10 64-bit and GPU is NVIDIA GT 540M
After installation, FFT on HF stopped working. After a couple of minutes the GPU crashed and Windows disabled the GPU.

Note: I had no issues like that...

SDR Console v3.0.27

IF Display On/Off toggle button does not work.

de JH5GON

The visual gain control behaves peculiarly. If the visual gain is set too high the radio overloads. If it is set too low the signal vanishes. The visual gains at which it misbehaves depend on the RF gain setting. This appears to be seen with several...

I receive an error after taking a screenshot when I select Open or Open with... . A message popup indicates: Windows cannot find 'C:\Users\PC\Pictures\SDR-RADIO.com (V3)\Screenshot-2021-02-09-001234.jpeg' Make sure you typed the name correctly, and...

Part of the Screen message:
SDR Console.exe caused ACCESS_VIOLATION in module C:\Program Files\SDR-Radio.com (V3)\libiio.dll at 0033:0000000063FE5AE5, iio_buffer_first()+21 byte(s)
This bug appears after about 1 minute, I had started the SDR...

In SDRPlay RSP1::SDR Console v3.0.26

In the Rec/Playback tab
clicking on the Record button in the Data:Record section brings up a Start Recording window.
It appears to be extending beyond the bottom of the screen. Screen shot attached.
Its start...

Hello Simon,

Further to my previous post about the Pluto uncommanded transmit bug when starting or changing bandwidth in Console.

As I noted, I first noticed a similar problem had newly occurred using Satsagen, the spectrum analyzer program for...