It's all about the Software

If audio pops & clicks are heard it may be necessary to re-enter the setting in Options-Audio-Buffering by changing it and/or restoring it to it's original setting. That seemed to correct a serious case of audio popping that occurred after...

It appears the Waterfall resolution is reset to default rather than that selected in the resolution menu after making changes to Satelllite or Favourite entries.
The example I can give is that I have selected x8 resolution ( Menu : View -...

The console is great and my favorite SDR software. I have a few questions,

Question 1
LimeSDR, set RX Ant=NONE: There are 3 spikes on the spectrum: 415.314MHz, 435.000MHz, and 454.686MHz. It looks like 435.000MHz is like a DC spike. The other two...

Hi simon,

I have a problem with the 3.0.28 console and my FDMS2.

When I change the bandwidth, my audio recording and my signal disappear

I've take 3 screenshot of Adobe audio and Console.

LB : 1.536MHZ = OK
LB : 3.072 MHz = X
LB : 6.144 MHz = X...

Bug report:

When recording a stereo FM station using the video recorder, the recorded audio is mono from the left channel and not stereo. Could this please be fixed?

Thank you so much. Loving the software, so many great features!

Andy618.

So I'm an amateur radio operator and I'm using SDRConsole V3 as my panadapter with direct control over my rigs (works great, thank you!). but when I'm say on 80m, I set the RX 1 audio output to the correct device and set the volume for my setup. But...

Hi Simon,

When using the SDR Datafile Editor and configuring output to be between certain times, the edit results are ok. The Finish time in the sequence box is however indicating the end time of the source file(s). See attached screenshot.

73,...

In 3.0.27 and also now in 3.0.28 (your latest build) the waterfall displays either a marker or signal on thye frequency slected.
If I retrieve the frequency from my favourites list no additional items are displyed in the waterfall and squeeze and...

I've been using the USB device server myUTN-2500 ( to connect my remote USB devices over the network, including Icom radios and SDR dongles, without using a dedicated computer.
I tested the R2, which was not recognized by the device server. After...

This bug is only present when noise reduction codec 2 is selected.
200hz audio tone overlays AM demodulation and is audible continually.
Tone also initially present on stronger SAM signals but quickly vanishes.
Also present on Wide-L, WIDE-U,...

Hello,
Since upgrading to version 3.026, I can no longer open Icon Select Radio.
When I open it, the sdr consol window freezes.
It is impossible to do anything. I can no longer select any radio station. Both locally and network... :(
Locally the...

Pointing towards our local broadcast FM mast signals can reach 80dBuV so are at the very limit of the S3 signal handling. Overloading can be mitigated by switching off the software preamp or adding some attenuation. The problem is when recorded...

Hey!

I got a SDRPlay RSPDx and I installed all drivers correctly but now if I wanna add the receiver, this message appears:

The problem is that my installed driver is too new or the SDR Console driver is too old

What can I do to fix this problem?

I recorded a .wav snippet from a playback of a larger recording while in Binaural SAM mode. When I listened to it, it played back in a slow manner. Not delayed, but like the recording was playing in half-speed so the voice came out real deep and...

Hi,

this is a crosspost, it first appeared here (I just joined the forum this morning):

I have found an entry in today's Windows Event Viewer that the SDRServerService.exe has crashed last night.

At that time, I didn't use it, and to be more...

I am using SDR Console with a Hermes Lite 2. Most times I start SDRC the meter bars go to some value and stay there during the entire session. Occasionally SDRC would start and operate correctly. Unfortunately the problem has only grown worse from...

HI....

I start SDR CONSOLE 3.0.27 and i receive this crash screen:

Image:

HookmouseProc?!?
I haven't changed anything since yesterday when it went
I use the SDRPLAY RSP2...

I'm solving by restarting and re-saving or resetting everything, but...

My name is Akira JA1OGZ. The SDR Console is very useful in receiving satellite telemetry. It works fine on other PCs.
It is a symptom that is occurring on the PC I am using now, but within a few minutes after starting up, it will enter Trap as shown...

Data Analyser works perfectly on the 1st analysis of each session. But moving on to a new project results in an image which appears “noisy” and overlaid with hash. In order to get a clear image it’s necessary to close the Analyser window and re-open...

Hi Simon,

If I take a screenshot with the Console (.27 3/24/21) on the second monitor it takes a screenshot of my main monitor. It never did that before.

Barry
WB2ZXJ

Hi

My SDR console has suddenly stopped working with my RTL SDR dongle.

It starts up and I select the dongle, but nothing shows up on the waterfall and no sound comes out the speakers.

And when I close SDR Console it crashes.

My RSP1a works fine...

Hi,
When editing a 46 Gb I/Q file (see I-Q file_editing-#1 ) to extract a 200 kHz wide full lenght portion, the size of resulting file is less than 100Mb and the file covers a few minutes only of the original file (see I-Q file_editing-#2 ).
Did I...

Ignore

Hello,
after update from 3.0.26 to 3.0.27 I always get an error dialogue at startup of SDR Console.
Manual press of Start button in the home menu, starts the device.
Version 3.0.26 could start directly one of my 2 two devices connected per USB.
Both...

I tried to schedule a recording.
I entered all the information, frequency, time, duration, audio format, etc.. But the OK button did not enable. So the schedule could not be saved.

Can you confirm that?

Thanks