It's all about the Software

Dear all,

I am running SDR Console Server/Client configuration at my home over a LAN network (between a garden house living room).
The problem is easy but frustrating. As soon as I launch the Console Client, I always need to set-up all the radio...

I'm searching for a used Anan 100D or equivalent.
73' Ron
ON2RON

I purchased a BladeRF x40 and XB-200 transverter board from a Nuand booth at DefCon several years ago and thought it would be interesting to use for ham radio. I forgot about it until I recently found it again and picked it back up. I've been very...

Running a IC7300 with an internal PTRX-7300 panadapter connected to an RSP1A SDR.

I have two RSP1A's and at SDR Console startup I select whichever I want to use. 99% of the time it's the RSP1A connected to the panadapter inside the 7300.

On...

Hi I am using an RSP1A and a Yaesu FTDX-5000 on start up I can see the radio is is tracking with the vfo and the digital display. I can select the radio the RSP1A and click start. However the Start button on the upper left does not start the...

SDR-Concole v3.2
Windows 10 22H2 build 19045.2251
Windows Feature Experience Pack 120.2212.4180.0
Hardware: AMD FX(tm)-8350 Eight-Core Processor 4.01 GHz
Graphics Card: NVIDIA GeForce GTX 750Ti - Driver version 526.98 released 20221116 (this was...

Hi,
I am considering building a small, low-power system using this board:

I see that the Intel® Celeron® 6305E Processor has internal UHD GPU with OpenCL 2.0 support. The idea is to use this for remote monitoring over RDP. Do you think this CPU...

An older (but still great specs) SDR...can I use it with SDR Console?

Um, that status bar is the official place for status information in Windows.
{o.o}

SDR Console's FM squelch appears to work off of signal strength. This means that any change in the broadband noise level will cause the squelch to blow open unless it's set so tight that weak but perfectly readable signals won't open it. Noise-based...

Will SDR Console run on Windows 11?

Hello,
I am trying to do FT8 on QO-100 with an Adalm Pluto SDR, on a 90 cm dish with a Othernet Bullseye LNB which is pretty stable
My Pluto has a GPSDO clock and I use the Geostationary Beacon feature, there is no drift at all.
A virtual audio...

Can I tune multiple receivers and route each output to a separate virtual audio cable?

Greetings all,

I had SDR Console working perfectly on my IBM ThinkCentre computer and had to do a computer reset. Ever since the reset and fresh install of SDR ConsoleI can only hear the audio thru the PC speaker. I cannot hear audio thru the sound...

When using SDR-Console in BC-FM mode (listening to a local radio station) I get quite bad distortion. I have been through all the settings to try and eliminate this but to no avail! :roll:

I've taken a video which I've posted on youtube, however,...

What are the spikes I can see tonight in the 6 Mtr ham band? Is it noise or harmonics of some frequency?

It looks like harmonics to me

Screenshot-2022-11-06-182038.jpeg

Hello,

I have a problem with SDR Console 3.2 lately.
Using WIN 8.1.

Since a couple of weeks when the SDR Console is started after I start the notebook from sleep mode.
The SDR Console starts and the waterfall is working but without any signal show...

Hello everybody,
Greetings and my best wishes!
Just registered, although was browsing this site for a while and like it very much. For some time, already, digging into SDR, but my interest, exclusively, in receivers. Have no intention to transmit. I...

Hello,

I am using SDR-Radio (v3.2) for QO-100 with a Pluto SDR. All working fine from the operating standpoint.

Now, I am wondering if there is a way to set the program up so that the TX frequency (on 2.4G) is sent via CAT rather than the RX (and...

Hello Simon and all,

I am just returning to the hobby and to this software, after spending most of the last two years in hospitals.

I am rusty. I have been unable to adjust either the software, or my video settings, to make the fonts and their...

Just wondering where do I send a crash report?

I have attached the report here anyway. Never mind it's too large.

I'm just wondering if any hams on here have a setup with their tranceiver and SDR Console, so they can monitor the ham bands on both SDR and their tranceiver on receive and be able to monitor their own transmissions on the SDR console on transmit...

To recreate the bug for RSP1A users (and possibly other radios where there is a latency setting option), do the following:

1. Start SDR Console and change bandwidth to anywhere between 6 MHz and 10 MHz.
2. Change latency to “Highest” (in Radio...

Is there a Scanner in Console?

If there is, that would make this super fantastic software! :D

A number of you may have either not used a phpBB style message board like this one before, being used to mailing lists, or have not done so for a long time.

I have put together a few hints and tips in the form of a FAQ, to help you get more out of...